Demco Autoslide Hitch For A 2011 Ram 2500

Question

Question:

I was going to purchase this model from a friend, but I have a 2011 Ram 2500 with rails in the bed not pucks… will this work?

asked by: Dominic B

0

Expert Reply:

Yes, The Replacement Head and Base Assembly for Demco Autoslide 5th Wheel Trailer Hitches # DM6077 can fit your 2011 Ram 2500, but you will need the side plates DM6003 to properly install it.

I attached an installation video link below.

expert reply by: Noah E

0

Answer 1

You definitely want to make sure that your hitch (5th wheel and/or bumper pull) is rated for more than the GVWR of your trailer. If you had a bumper pull that was rated a few hundred pounds over the GVWR of your trailer then I would say that you are…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 6

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 7

Yes you are - all 5th wheel hitches are going to require some type of rails in order to be used. So you'd need #DM8552016-71 for your 2006 Dodge Ram.

view full answer...

Answer 8

A wedge is needed, yes, and the Lippert Turning Point pin box does come with a universal wedge, but it is not a very good fit with the B&W Companion #BWRVK3710. So I highly recommend instead using the 5th Airborne Custom Wedge for B&W Fifth…

view full answer...

Answer 9

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 10

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 11

The Patriot Slider part #BWRVK3270 might be a bit more noisy than the Companion slider part #BWRVK3400 due to the increased number of mounting points, 4 at the corners vs. 1 in the center. Probably not that noticeable and certainly not something…

view full answer...

Answer 12

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Demco Autoslide Hitch For A 2011 Ram 2500

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching