What are the Dimensions of the Replacement Spout for Phoenix Faucets PF181004

Question

Question:

Can you tell me the height of this replacement faucet, and the horizontal distance from the attachment to the aerator i.e., when mounted, how far does the end extend from the attachment to the counter?

asked by: Tom

0

Expert Reply:

The replacement spout part # PF181004 is 8 inches tall and sticks out 7-1/4 inches from where it attaches to faucet base.

expert reply by: Jameson C

0

Answer 1

The Buyers Products #337B1018LSP do not come with any mounting hardware, since the method of mounting is going to vary from vehicle to vehicle. Ideally you will use the factory fasteners on your vehicle to secure it into place and locally sourced…

view full answer...

Answer 2

I spoke with Phoenix faucets, and they said the length of the Replacement Hi-Spout for Phoenix Faucets #PF181003 is 8" from the base to where the water drops.

view full answer...

Answer 3

For your 2008 Dodge Ram 2500 long bed you'd need to go with Torklift Frame Mounted Camper tie downs with the part numbers #TLD4101 and #TLD3109 since the length of your camper would be longer than your truck bed. The bed mounted tie downs can…

view full answer...

Answer 4

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 5

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 8

In regards to the Correct Track Trailer Alignment and Lift Kit part #RR23QX, the kit provides a lift by essentially extending the hangers. This normally requires cutting off the old hangers and welding on new, taller ones but with this kit you…

view full answer...

Answer 9

The Correct Track Trailer Alignment and Lift Kit - Tandem Axle #RR23QX does come with all of the components needed to lift a tandem axle trailer. The center hangers of a tandem axle setup use different components than the front and rear hangers since…

view full answer...

Answer 10

The Correct Track Trailer Alignment and Lift Kit part #RR23QX offers a 1-1/4" or 2-1/4"lift so if the hitch height height is lower than the vehicle hitch height you can use this kit to bring the trailer level with the vehicle and eliminate…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

What are the Dimensions of the Replacement Spout for Phoenix Faucets PF181004

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching