How Tight to Torque Down Hardware of Timbren Axle-Less Trailer Suspension System # ASR1THDS03

Question

Question:

What is the torn spec for the bolts on my timbren axles please and thank you

asked by: Kieto

1

Helpful Expert Reply:

The 1/2 inch UNC gr 8 bolts that your Timbren Axle Less Kit part # ASR1THDS03 was installed with would need to be torqued down to 90-95 ft lbs of torque according to the install instructions.

expert reply by: Jameson C

1

Answer 1

Timbren Axle-Less Trailer Suspension for Off-Road Tires #ASR1THDS03 has maximum deflection of 3-3/8-inches when used within its rated weight capacity. This is noted in the linked diagram. For off-road use the improved ground clearance from completely…

view full answer...

Answer 2

I just spoke with my contact at Timbren who said that if you are towing your trailer dry right now at the 1,300 lbs then that is why it is a little rough. Since the Timbren Axle-Less Trailer Suspension System #ASR1THDS03 is rated for 2,200 lbs you…

view full answer...

Answer 3

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 7

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 8

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 9

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 12

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

How Tight to Torque Down Hardware of Timbren Axle-Less Trailer Suspension System # ASR1THDS03

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching