Screen Door Slide for 2004 Holiday Rambler

Question

Question:

We need slide cover for screen door 11/2”-13/4” deep 11 5/8” H x 11 7/8”W Is this available and what part number? Thanks

asked by: Dan P

0

Expert Reply:

Based on what you mentioned we have the Replacement Slide for P-Series RV doors part # A77018 which is 11-15/16 inches long and 11-7/8 inches wide. This would work as a replacement for what you have now.

expert reply by: Jameson C

0

Answer 1

As you have a Coleman Mach system currently you can use the Furrion Chill AC units from the list below. These will simply replace only the rooftop units and the controls and thermostats you currently have in place with control the new AC's. 13.5K…

view full answer...

Answer 2

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 3

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 4

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 5

Yes, you will be able to use the Furrion Chill HE RV Air Conditioner System #FR87FJ to replace all your Coleman MACH components. The thermostat will be able to control your furnace and run off the thermostat wiring your Coleman AC uses.

view full answer...

Answer 6

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 7

The Weld-On Hinge w/ Brass Bushing and Grease Zerk part #MA79ZR doesn't have a listed weight capacity. That said, it uses a 5/8" diameter solid steel pin so the limiting factory would likely come down to the weld. The more hinges you have,…

view full answer...

Answer 8

Yes, the Replacement Jack for HappiJac Truck Camper Jack System part #LC736514 (Model 4220) will fit your HappiJac Truck Camper Jack System Model 4150. If you need a new gearbox/motor then we have that as well, the Replacement Motor and Gear Head…

view full answer...

Answer 9

I went out to the warehouse to measure a jack and handle included in the Leveling Scissor Jack Set, #JSC-24. When compressed, the distance from the end of the crank bolt head to the center of the jack (between the two brackets) is 13-7/16 inches.…

view full answer...

Answer 10

The parts you mentioned are not available as replacement parts so the best we can offer will be a new 12 volt fan with a manual lift. What you can use in its place is the Ventline Ventadome Trailer Roof Vent with 12V Fan - Manual Lift #V2094SP-30.…

view full answer...

Answer 11

Yes, it looks like your existing Fan-Tastic Fan model 4000BT is a standard 14" wide x 14" long roof vent so the MaxxFan Deluxe Roof Vent w/ 12V Fan and Thermostat part #MA00-05100K would fit the opening for your old vent as long as the roof…

view full answer...

Answer 12

There isn't a master cylinder replacement we can offer that will fit an Atwood surge coupler since Atwood had a unique design and unfortunately isn't around any more. Best solution is a new actuator like the part #DM72VR for drum brakes or…

view full answer...

Screen Door Slide for 2004 Holiday Rambler

Product Page this Question was Asked From

Continue Researching