Troubleshooting Pitch Arm Not Staying Put on Solera Smart Arm 12V Power RV Awning

Question

Question:

After pulling down the arm to adjust pitch it goes back to its original position. What are we doing wrong?

asked by: Stephen P

0

Expert Reply:

If the pitch adjustment isn't staying in place for your Solera Smart Arm 12V Power RV Awning # LC517505 then you'll need to adjust the bolt (B) in the center of the joint to tighten up this function. Attached is a photo showing the location of the bolt.

expert reply by: Jon G

0

Adjustment Bolt (B) Location on Solera Smart Arm Awning
(click to enlarge)

Hob

3/24/2024

i have done that adjustment as tight as i can put 250 pounds behind. What would be the next solution. Thanks HOB

Reply

Jon G.

3/28/2024

@Hob Just to double check, are you using a 1/2" wrench to tighten the nut while also using a 1/4" hex wrench to hold the pitch arm?

Reply

Answer 1

You can check the condition of your hub's races by carefully removing all bearing grease with a rag to expose the actual surface of the races. When they are completely free of grease, etc., inspect them for any signs of scoring (very slight…

view full answer...

Answer 2

Bearing Kit #BK3-100 consists of bearings 15123 and 25580, matching races, grease seal and cotter pin. This kit is intended for a 6K axle. The same component parts are found in Lippert bearing kit 333950, also rated for a 6K axle. Two helpful…

view full answer...

Answer 3

According to my research the correct replacement bearings are parts #25580 and #LM67048 with the replacement seal being part #GS-2250DL. These are available in the Bearing Kit #BK3-300. Just make sure that you have these bearings and that your seal…

view full answer...

Answer 4

For your over cab bed, we have the Surco RV Bunk Ladder - 1" Wide Hooks - 60" Long #SP501B or the Stromberg Carlson RV Bunk Ladder - Aluminum - 60" Tall #LA-460. These are also available in 66 inches long #SP504B and #LA-466. I…

view full answer...

Answer 5

Most slides have EPDM rubber roofs but because EPDM is rubber it requires treatment each year to keep it soft and prevent shrinkage. You could replace it with TPO which is another synthetic rubber that will last longer than the EPDM. The smallest…

view full answer...

Answer 6

The Alpha Systems Superflex TPO RV Roof Membrane #AL25CV is 0.30" thick. This is the only thickness they offer currently for the TPO. You will need the Alpha Systems RV Roof Replacement Installation Kit #AL63FJ to install this roof membrane.

view full answer...

Answer 7

We do have the panels separately. What you're looking for is the Go Power Overlander Expansion Kit - 200 Watt Solar Panel #34282182.

view full answer...

Answer 8

When installing an awning like the Solera Smart Arm 12V Power RV Awning #LC517486, the arms will be secured to the wall framing. When the awning extends there will be quite a bit of leverage, so it is important to mount the awning to an area where…

view full answer...

Answer 9

The Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR is a single zone 3 wire thermostat like the one you are describing. I have attached the wiring diagram for this thermostat and the control box below for your reference.

view full answer...

Answer 10

The Alpha Systems Superflex TPO RV Roof Membrane #AL32CV is 30 mils thick. You will need the Alpha Systems RV Roof Replacement Installation Kit #AL74UV to install and seal the membrane on your roof.

view full answer...

Answer 11

Hey David, we've used the LaSalle Bristol RV Roof Vent install kit part #344270KITW to install several MaxxFan RV roof vents and it's worked well so it would also work well for you. This comes with everything needed so it would be a great…

view full answer...

Answer 12

Yes it will accept PVC adhesive, the felt backing will soak it up and help create a strong connection/bond. The adhesive has a longer life span than butyl tape and it is cleaner than using caulk or other sealants. It will need to be treated with…

view full answer...