Recommended Replacement Jacks For A 2014 Jayco Eagle Premier Fifth Wheel

Question

Question:

I need to replace the front leveling legs and associated motor on my 2014 Jayco Eagle Premier 321 RLTS. Who manufactures replacement legs that will fit this model? The outer sleeve of each of the legs is 34.5 inches long, and the weld stops on the sleeve are 17.5 inches outside to outside and 15.5 inches inside to inside. I have contacted other manufacturers of replacement legs Stromberg Carlson and Lippert, but none make a model with that specific sleeve length and weld stop length. The manufacturer of the existing failed legs is Atwood, who no longer makes replacement parts for landing systems.

asked by: Warren H

0

Expert Reply:

For your 2014 Jayco Eagle Premier 321 RLTS, I recommend taking a look at the :

-Bulldog Tandem Landing Gear Set # BD500162.

These jacks feature 36" of lift, a combined weight capacity of 8,000-lbs, has an outer tube width of 2-1/2", and an inner tube width of 2-1/4".

expert reply by: Bryce D

0

Answer 1

Good news! I was able to go out to the warehouse and measure the etrailer landing gear #RVLG-8HDL for you. I found that the distance between the weld stops from the outside to outside is 17-1/2 inches and from the inside to the inside of the weld…

view full answer...

Answer 2

Yes, based on the distance between the welded on brackets of your camper the etrailer landing gear set part #RVLG-8HDL will fit on your 2021 Forest River Cherokee Wolf Pack. The motor normally used with this kit is the part #LC142178. If the motor…

view full answer...

Answer 3

It definitely sounds like the internal gears on your existing landing gear system are shot so a complete replacement is your best option. I'm not able to track down what specific model system would have been installed at the factory on your…

view full answer...

Answer 4

The Landing Gear Set w/ Handle #RVLG-8HDL that you're interested in sounds like to be a perfect match for you! This landing gear set has an overall width of 6-1/8" including the foot pad, and the legs itself measure 2-1/2" wide like…

view full answer...

Answer 5

The Bulldog #BD500162 landing gear bolts to its brackets, but the brackets would weld to the trailer frame. You should be able to reuse your existing brackets as long as they're not damaged or excessively corroded. The jacks would be the correct…

view full answer...

Answer 6

I have attached a photo for you that shows how to properly measure the outer tube on a landing gear leg. I have not heard of a landing gear leg with a 36-1/2" long outer tube so if this is what you have then I recommend you replace both the lead…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

To determine the best landing gear option for your 1997 Forest River Sierra you'll need to measure the where your weld-stops sit to see if there is a matching set so that you can swap over without having to cut off the old mounting brackets and…

view full answer...

Answer 11

For your 2018 Ram 2500 with the factory puck system the best 5th Wheel Hitch is the B&W OEM Companion. If you have the 8 foot bed then you will want the fixed 25K #BWRVK3600 and if you have the short 6-1/2 foot bed you will need the 20K Slider…

view full answer...

Answer 12

The sure way to pick out replacement landing gear for a trailer that will bolt right up to the current brackets is to measure the distance between the mounting brackets (underside of top bracket to top of lower bracket as shown in the diagram) if it…

view full answer...

Recommended Replacement Jacks For A 2014 Jayco Eagle Premier Fifth Wheel

Product Page this Question was Asked From

Continue Researching