Replacement Landing Gear for 2004 Carriage 5th Wheel Trailer
Question:
My landing gear has stopped raising and lowering hand crank will not move it eaither. Do you know whst kind of landing gear it has and what do i need to replace?
asked by: Race H
Expert Reply:
It definitely sounds like the internal gears on your existing landing gear system are shot so a complete replacement is your best option. I'm not able to track down what specific model system would have been installed at the factory on your 2004 Carriage 5th Wheel Trailer but I can absolutely help you find a compatible replacement.
The Bulldog Tandem Landing Gear Set # BD500162 for manual operation that you were looking at will likely work great. It features standard weld stop/bracket dimensions of 15-1/2 inches from inside to inside and 17-11/2 inches from outside to outside (see attached image).
What you can do is measure your existing brackets to make sure these will bolt right up to them. If you happen to have different spacing just let me know and I can see if we have a different system that will match up. Otherwise you can simply cut off your current brackets and weld on the new ones that will come included with the landing gear.
I have included a short video demonstration and the written installation/operation manuals that you can look through.
Product Page this Question was Asked From
Bulldog Tandem Landing Gear Set - Drop Leg - 36" Lift - 8,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 7001 - 8000 lbs
- Landing Gear
- Sidewind Jack
- 36 Inch Lift
- Bolt-On
- 2 Jacks
- Bulldog
more information >
Continue Researching
- Shop: Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Shop: Landing Gear Set - 36-1/2" Lift - 8,000 lbs
- Shop: Bulldog Tandem Landing Gear Set - Drop Leg - 36" Lift - 8,000 lbs
- Search Results: lc142178
- Video: etrailer Landing Gear Set Review
- Video: Bulldog Camper Jack - Landing Gear - BD500162 Review
- Shop: Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
- Shop: Stromberg Carlson Manual Landing Gear Set - Weld On - 34-7/8" Lift - 8,000 lbs
- Q&A: How to Know if Landing Gear Set # RVLG-8HDL Will Fit 2001 Sunnybrook 31BWFS
- Shop: Replacement Gearbox for etrailer and Ram 5th Wheel Landing Gear
- Shop: Lippert Electric Landing Gear Set - Weld On - 37" Lift - 6,000 lbs
- Q&A: Troubleshooting Trailer Landing Gear Motor that Skips/Clicks when Activated
- Video: Review of etrailer - Trailer Jack,Camper Jack - RVLG-RDBOX
- Search Results: landing gear
- Video: etrailer Camper Jack - Landing Gear - RVLG-8000 Review
- Shop: RV Power Cord
- Video: Review of Lippert Components - Trailer Jack,Camper Jack - LC146059
- Q&A: How to Know What Trailers Bulldog Landing Gear Will Fit
- Q&A: Troubleshooting Landing Gear on Fuzion Toy Hauler That Will No Longer Lift Trailer
- Q&A: Bracket Dimensions of the etrailer RV Landing Gear System # RVLG-8HDL
- Search Results: wheel center cap 3.19
- Search Results: spring loaded pull pin
- Search Results: fifth wheel landing gear
- Search Results: fifth wheel king pin
- Search Results: fifth wheel skirts
- Q&A: Upgraded Landing Gear Motor for a Keystone Challenger 5th Wheel
- Shop: Wheel Liners
- Video: Stromberg Carlson Landing Gear Spring-Loaded Pull Pins Review
- Video: Lippert Components Trailer Jack LC142178 Review
- Q&A: Outside Leg Dimensions of etrailer.com Landing Gear for 1995 Skyline Layton Fifth Wheel