Hitch Adapter Needed for 12" or 14" Drop

Question

Question:

Do you have one with a 12 or 14 onch ?

asked by: Bill

0

Expert Reply:

We do!

We have the Gen-Y Hitch Replacement Shank # 325-GH-506 which has a 12-1/2" drop and then the Gen-Y Replacement Shank # 325-GH-307 which has a 15" drop.

Since these have such a large amount of drop we do also recommend using the Adjustable Stabilizer Bar Kit # 325-GH-0100 as well so the shank stack doesn't twist or turn during travel.

Attached are some review videos for you to check out.

expert reply by: Jon G

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 5

I recommend using the Curt Lock Set #C23556 for your Curt Adjustable 2-Ball Mount #C99NR. This comes with a lock for the hitch receiver and one for the ball mount platform. Even though your platform uses 2 pins, only 1 locking pin is needed to secure…

view full answer...

Answer 6

Hey Buddy, so the Fastway Adjustable Ball Mount part #DTSTBM6825-2S is a really great choice for the 2-1/2 inch hitch of your 2021 Ford F-250 which is going to be very solid in your hitch due to it's built in anti-rattle device that is easy to…

view full answer...

Answer 7

I do have a solution for you, however I do not recommend using the Roadmaster Dual Hitch Receiver #RM-077-10 in conjunction with the High-Low Adapter #RM-048-10 that you already have. Using an adapter with another adapter like this will cause a…

view full answer...

Answer 8

The Gustafson RV Puck Light #277-000343 can be used with a dimmer switch but the dimmer switch needs to be designed for use with LEDs. Otherwise if you use a non-LED dimmer when you go to dim the lights they might flash and make a weird noise at the…

view full answer...

Answer 9

I wasn't able to find any model information on your Sunlink RSBF3NN-008 and we don't carry that particular brand, but we do have a number of recessed puck lights available that may work for you. You may be able to use the Gustafson RV Puck…

view full answer...

Answer 10

We have heard of this issue before on the Lippert Ground Control systems #LC358590. Here is the recommended procedure for clearing the error code: Extend all jacks at least 6 inches. Then press and hold the RETRACT button until the jacks begin…

view full answer...

Answer 11

How thick are your D-rings? We have two options that will work but you have to know the size of them. If you have 3/4 inch thick D-rings you need the part #RM-035 as an adapter or if you have 1 inch thick D-rings you need part #RM-035-1. In addition…

view full answer...

Answer 12

Typically when the Quick Level Touch Pad #LC74FR red light flashes it indicates an error and the retract button flashing green it means that the error has been reset. The issue appears to be on the extending, so it's possible that there's…

view full answer...

Hitch Adapter Needed for 12" or 14" Drop

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching