Replacement Parts For A Leer Tri-Fold Hard Tonneau Cover

Question

Question:

I need the 2poles with new locks for a leer trifold hard top

asked by: Mike E

0

Expert Reply:

By poles I'm assuming you're talking about the gas struts that hold the cover up against the rear window. These poles can be replaced with the Replacement Prop Rod Assembly for Leer Tri-Fold Tonneau Covers # LE72RR. We also carry the Replacement Prop Rod Clips For Leer Tonneau Covers # LE22RR incase you need to replace those as well.

If by locks you mean you need the latches that allow the covers to lock into place then you'll need the Replacement Cync Latch for Leer Tonneau Covers, part # LE82RR.

expert reply by: Kevin C

0

Answer 1

For your Leer Hard Tonneau Cover #LE59VR, you'll want the Replacement Adjustment Bolts and Nuts for Leer SR250 Soft Tonneau Covers #LE32RR, and the Replacement Clamps for Leer SR250 Soft Tonneau Covers #LE52RR on your 2018 Toyota Tacoma short…

view full answer...

Answer 2

I spoke with a representative from Leer. You need these parts for the Leer Hard Tonneau Cover - Tri Fold - Fiberglass Reinforced Plastic, part #LE49VR, on your 2009 Toyota Tacoma: Prop Rod Assembly, part #Replacement Prop Rod Assembly for Leer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...