Correct MORryde StepAbove RV Steps for 2020 Grand Design Momentum 29G

Question

Question:

I would like a set of the MORryde solid steps that fold into the camper door. I have a 2020 grand design momentum 29g. The door measures 27 1/4 inside frame and 26 1/2 at the lip that the door seals against. Which step would I need? Thanks.

asked by: Shaun C

1

Helpful Expert Reply:

The MORryde StepAbove RV Steps for 23-3/4" to 26-1/4" Wide Doorways will be correct for a 2020 Grand Design Momentum 29G. That said, you'll need to measure the entry height to get the correct model; part # MR26RR for 25-29", part # MR98RR for 30-33-1/2", or part # MR48RR for 34-36".

expert reply by: Conner L

1

Answer 1

Part 300-020885 refers to an EZ Loader boat trailer BT150/B151 bearing kit. Part #300-020883 refers to a complete 5-on-4-1/2 idler hub kit that includes races, bearings, seal, washers, nut, retainer nut and cotter pin, bearing protector and lug…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

While we do not carry that particular Lippert step we do have the similar MORryde #MR98RR or a better option in my opinion is the TorkLift GlowStep #TLA9104. I prefer this step as it folds up nicely and works better in tight areas like storage lots.…

view full answer...

Answer 6

Hey Beatrice, To find the right fit for your trailer's suspension you'll need to take a quick measurement of your current shackle straps. You'll need to measure from the center of one bolt hole to the center of the other bolt hole. The…

view full answer...

Answer 7

The Dexter 8-427 hub is no longer available. Even looking through Dexter's site the only references to it are replacement bearings. You can use a wheel with a larger pilot hole as long as the wheel attaches to the hub using lug nuts and not…

view full answer...

Answer 8

If you are just looking for a new converter, the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers part #PD4635V will be a direct upgrade for the Magnetek Converter Series 6300 Model 6332 that you have now.

view full answer...

Answer 9

Hey Jeff, from previous customers who have given us the part number you mentioned we have found that the matching MORryde StepAbove is the part #MR65RR which has 23.5 inch wide steps and is a 3-step setup with the strut assist.

view full answer...

Answer 10

Hey Dave, the MORryde upgraded shackle kit part #MR76ZR that you referenced is compatible with your 2020 Grand Design 2670MK and the Lippert Road Armor equalizers.

view full answer...

Answer 11

The difference is between just the MORryde Locking RV Storage Box #MR43RR and when you add the brackets at their widest setting. Just the box measures 25-3/4" but when you add the mounting brackets is when you'll see that 27-3/4" width…

view full answer...

Answer 12

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...