What Is In The Replacement Power Wire For Voyager Digital Wireless Camera Kit?

Question

Question:

Is this for the bracket too or just harness?

asked by: Nicholas F

0

Expert Reply:

The Replacement Power Wire for Voyager Digital Wireless Camera # PSVCWVCMS130AP does include the bracket.

This kit also includes 2 washers, 6 Allen head bolts as well as the needed Allen key for installation.

expert reply by: Bryce D

0

Answer 1

Yes, we do have the power wiring piece for the Voyager Camera WVCMS130AP that you referenced. It is found as part #PSVCWVCMS130AP on our site. I confirmed with my contact at Voyager that this is the correct part you need.

view full answer...

Answer 2

There were two different style cameras that came in the WVOS511 kit, which has since been discontinued. Each of the cameras had different antennas. One is straight on the newer model camera and the one has an elbow type on the older camera. An easy…

view full answer...

Answer 3

The pre-wiring of Furrion pre-wired RVs is basically just two wires as well as the Voyager harness like part #PSVCWVCMS130AP. One wire is the power wire which is the running light circuit and then the other is the ground so it really would just be a…

view full answer...

Answer 4

You can use the power and ground from your current Voyager wiring to connect the Replacement Power Wire for Voyager Digital Wireless Camera #PSVCWVCMS130AP, yes. Just be sure that you also use a wireless monitor that's compatible with the camera.…

view full answer...

Answer 5

Yes, this cable is compatible with your Voyager camera system. The cables come in varying lengths. Adding the correct length cable extension should remedy your problem. Voyager Camera Extension Cable - 10' Long, part #VGR94FR Voyager Camera…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

What Is In The Replacement Power Wire For Voyager Digital Wireless Camera Kit?

Product Page this Question was Asked From

Continue Researching