Can The Big Adjustment Screw Be Removed From The Rear View Safety Windshield Mount Arm?

Question

Question:

Does the 6 sided mounting piece completely unscrew and come out?

asked by: Debra

1

Helpful Expert Reply:

I went out to the warehouse and attempted to unscrew the screw on the:

-Rear View Safety Windshield Mounting Arm for Mirror Monitors # RVS-619UM, and was unable to unscrew it from mount as it appears that, that part is permanently positioned in the mount.

expert reply by: Bryce D

1

Answer 1

The Rear View Safety Windshield Mounting Arm #RVS-619UM is capable of supporting a monitor that is up to 3lbs and can mount with the windshield style mirror mounting bracket. It was designed for use with their Rear View Safety Universal Mirror…

view full answer...

Answer 2

No, the only compatible mount for the 7" Furrion monitor #FR47FR is the #FR79SR, which will suction cup to your windshield.

view full answer...

Answer 3

I may have an option that will work for you, however we are only a retailer, not an actual trailer hitch manufacturer. We do not make any of the products that we sell. To have a hitch custom made, you will most likely have to contact a custom…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Can The Big Adjustment Screw Be Removed From The Rear View Safety Windshield Mount Arm?

Product Page this Question was Asked From

Continue Researching