Availability of Ladder Rack that Can fit Tracks of RetraxPro Tonneau Cover

Question

Question:

what ladder racks are compatible with retrax pro tonneau cover

asked by: Gordon K

0

Expert Reply:

The Yakima Overhaul HD # Y01151-58 with the Tonneau Cover Adapter Kit part # Y01155 is a really nice ladder rack that fits the channels of the Retrax Pro tonneau covers. We also have the TruXedo Elevate Truck Bed Rack System # TX46NV which has telescoping load bars that go from height of 18 to 28 inches. Based on the versatility of the Elevate that would be my recommendation.

expert reply by: Jameson C

0

Answer 1

If you have the 6.2 V8 engine in your 2017 Ford F-250 Super Duty than the maximum tongue weight rating is 1,500 lbs and you would not benefit from replacing the factory trailer hitch but if you have the 6.7L V8 engine then the maximum tongue weight…

view full answer...

Answer 2

The Truxedo Elevate bed rack part #TX46NV that you referenced is compatible with kayak and bike carrier from Yakima and Thule. Since this rack has channels on top of the bars the racks would easily fit directly to them like with the Thule ProRide XT…

view full answer...

Answer 3

As long as the tonneau cover on your 2018 Ford F-150 6-1/2' bed has rails that mount inside your bed you have a few ladder rack options. For one that will for sure work we have the Thule TracRac SR Sliding Truck Bed Ladder Rack #TH43002XT-501.…

view full answer...

Answer 4

The TruXedo Elevate Truck Bed Rack System - 18" or 28" - Aluminum would be a great choice for your 2013 Ford F-250. The main reason you saw a Yakima recommendation like the #Y01151-58 is due to the fact that we did not offer the Elevate…

view full answer...

Answer 5

I have a solution for you, but the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack - Aluminum - 500 lbs - 68" Crossbars #Y01151-58 is specifically made to work with the Retrax XR tonneau cover and will not work with your BAK Revolver X4…

view full answer...

Answer 6

For your 2021 Ford F-250 6-3/4 ft bed that has a Bak Revolver installed on it we have great ladder rack solutions like the TruXedo Elevate Truck Bed Rack System #TX46NV which is similar to the Yakima Overhaul but the Overhaul cannot fit a truck that…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only tonneau…

view full answer...