Availability of B and W Companion Slider Base RVB3670

Question

Question:

I’m looking for just the slider base, rvb3670. If you wind up with one, PLEASE let me know

asked by: Nic

0

Expert Reply:

We do have the B and W Companion Slider base part # BWRVB3670 that you are looking for. The product link is down below or you can click the hyperlinked text.

expert reply by: Jameson C

0

Answer 1

Yes absolutely! To use your B&W Companion OEM 5th Wheel Trailer Hitch w/ Slider for Ram Towing Prep Package - Dual Jaw - 20K #BWRVK3670 with your new 2021 Ram 2500, you'll just need to swap the base out with the: -Replacement Slider Base for…

view full answer...

Answer 2

To use the B&W Companion 5th Wheel Trailer Hitch #BWRVK3500 from your 2011 Ram 2500 SLT Crew Cab Long Bed in a 2021 Ram 3500 Big Horn Crew Cab Long Bed with the OEM Pucks you will be able to use the head assembly but will need to replace the base…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Yes, the head from your Companion hitch #BWRVK3500 would fit on the base part #BWRVB3705 you also referenced.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 11

The factory prep package or pucks are not the same between Ram, GM and Ford. The spacing is all different which means you cannot use a 5th wheel hitch for Ram pucks on a GM with pucks. Take the Curt A25 5th Wheel Trailer Hitch for example which is…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Availability of B and W Companion Slider Base RVB3670

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching