Does the Reese Fifth Wheel Bracket Kit # RP58386 Come with All Hardware

Question

Question:

does this kit come with all hardware,brackets,bolts etc

asked by: Alfred P

0

Expert Reply:

The Reese Installation Kit for 5th Wheel Trailer Hitches # RP58386 does come with all the hardware to install into the bed of a truck. The only thing it would need for a hitch to be installed would be a set of base rails. For that you would want the Reese Universal Rails part # RP58058.

expert reply by: Jameson C

0

Answer 1

Most likely it's a 10 bolt design that is on your 1989 Chevy C/K 3/4 Ton 4X4 2500. Generally speaking we do not recommend mixing bracket and rail manufacturers. The best solution for you would be to determine what bracket kit you have in the bed…

view full answer...

Answer 2

Reese Universal 5th Wheel Base Rail kit #RP30035 does require drilling since it is intended to fit a wide range of trucks. The Reese semi-custom base rail kit #RP30035-386 for the 2018 Ram 1500 includes the same base rails and hardware as part…

view full answer...

Answer 3

I attached a link to the install instructions for the Curt bracket kit part #C16306 that you referenced to this page.

view full answer...

Answer 4

The Reese Rail Kit part #RP50142-58 that you referenced is a confirmed fit for your 2012 Ram 1500 and is compatible with the mounting tabs of your RBW fifth wheel hitch. Your hitch is made to the industry standard dimensions which is what this rail…

view full answer...

Answer 5

On the Reese Fifth Wheel Universal Installation Kit, #RP30035, the standard dimension between the base rails is 22 inches on center apart. The measurement that is used to install the universal base rails is from the rear edge of truck bed to the rear…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 10

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 11

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...