Weight Capacity of RackEm Shelf Kit for Enclosed Trailers Part # RA-13

Question

Question:

This product states it can hold up to 500lbs. Is this per shelf or total weight?

asked by: Craig

0

Expert Reply:

The 500 pound capacity for the RackEm Shelf Kit, part # RA-13, is for total weight.

expert reply by: Patrick B

0

Answer 1

We have multiple options in 12', 18' and 24' lengths. My recommendation is the Small Coin Pattern, #TS67FR at 18' length with additional 12' from the #TS57FR. For wood flooring, use either RV Flooring Adhesive for Vinyl Over Wood,…

view full answer...

Answer 2

You can absolutely install E-Tracks like the etrailer Horizontal E-Track - Black Powder Coated Steel - 2,000 lbs - 94" Long - Qty 4 #e42VR you were looking at in your Forest River Enclosed Cargo Trailer yourself. Now there are a few things to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Weight Capacity of RackEm Shelf Kit for Enclosed Trailers Part # RA-13

Product Page this Question was Asked From

Continue Researching