Sway Bracket Jackets For Quieting Fastway E2 Weight Distribution Hitch

Question

Question:

Will the jackets for Equal-i-zer work on a Fastway e2 W/D hitch? Thanks!

asked by: George H

0

Expert Reply:

Yes, the Equal-i-zer Sway Bracket Jackets # EQ95-01-5150 can be used with your Fasteway E2 Weight Distribution Hitch

expert reply by: Bud M

0

Answer 1

Yes, the Sway Bracket Jackets for Equal-i-zer Weight Distribution Systems #EQ95-01-5150 you have will work great with the Replacement L-Pins and Clips for Equal-i-zer Weight Distribution Systems #EQ95-01-9430. Attached are a couple of videos for you…

view full answer...

Answer 2

To lubricate the hitch ball for your Andersen Weight Distribution System I recommend using White Grease #58117. This particular grease is designed specifically for this type of application and will do a great job of reducing friction and protecting…

view full answer...

Answer 3

We have what you need for your Fastway e2 Weight Distribution System #FA94-00-1000, which is the Sway Bracket Jackets for Equal-i-zer Weight Distribution Systems #EQ95-01-5150. I have to note also, that using these pads may slightly diminish the…

view full answer...

Answer 4

While I have never seen them made of rubber there are the Sway Bracket Jackets #EQ95-01-5150 made of plastic. These were designed for those who found the noise to be excessive between the metal brackets and spring bars. They are made by Equal-i-zer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 11

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 12

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Sway Bracket Jackets For Quieting Fastway E2 Weight Distribution Hitch

Product Page this Question was Asked From

Continue Researching