Will The Draw-Tite Center Section For Hide-A-Goose Fit The Curt EZr Under-Bed Gooseneck System?

Question

Question:

Im wondering if a drawtite center section will work with a Curt gooseneck under bed system

asked by: Keith P

1

Helpful Expert Reply:

I took a look at the Center Section for Hide-A-Goose Underbed Gooseneck Trailer Hitch # 9468, and the Curt EZr Double Lock Underbed Gooseneck Trailer Hitch with Installation Kit # C75KR, and the:

-Center Section for Hide-A-Goose Underbed Gooseneck Trailer Hitch # 9468 will actually not work with the:

-Curt EZr Double Lock Underbed Gooseneck Trailer Hitch with Installation Kit # C75KR, due to the fact that # 9468 is too wide, measuring in at 1' x 1', while the center section measures in at 7-3/4" x 24-1/2".

If you needed the center section for the Curt Underbed Gooseneck Hitch, you can use the:

-Center Section for Curt EZr Double Lock Underbed Gooseneck Trailer Hitch # C60611.

expert reply by: Bryce D

1

Answer 1

The Curt X5 adapters are designed to fit specific gooseneck hitches. If you have a B&W Turnoverball gooseneck the X5 adapter that can be used is part #16310. If you have the Curt Double Lock gooseneck then the X5 you need is part #C16210. If you…

view full answer...

Answer 2

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 5

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 10

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 11

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Will The Draw-Tite Center Section For Hide-A-Goose Fit The Curt EZr Under-Bed Gooseneck System?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching