Correct Camper Tie Downs For 8 Foot Bed 2019 Ram 3500 SRW Diesel Crew Cab

Question

Question:

Hello - I have a 2019 Ram truck, crew cab, cab length running boards with 8' bed, SRW diesel. . I am looking for tie downs for a truck camper. I am seeing conflicting info concerning the Torklift TLD2140 concerning if they will work with running boards or not. Again, my running boards only go as far as the end of the cab.

asked by: JAMES M

0

Expert Reply:

I checked with Torklift, the front mount TorkLift Custom Frame-Mounted Camper Tie-Downs, # TLD2140 is the correct part number for a 2019 Ram 3500 crew cab with 8' bed, running boards under cab, SRW diesel. For the rear you will want TorkLift Custom Frame-Mounted Camper Tie-Downs, # TLD3112.

I recommend the TorkLift Locking FastGun Turnbuckles for Frame-Mounted Tie-Downs, # TLS9526-2-LK be used with these camper tie-downs.

Please note the linked product videos.

expert reply by: Michael R

0

Answer 1

We do have camper tie-downs that will fit on your 2019 Ram 2500 but since you have the running boards none of the TorkLift Tie-Downs will fit. You could use parts #TLD2140 and #TLD3113 if you removed the running boards (or steps) but since I doubt…

view full answer...

Answer 2

Congratulations on your new truck bed camper! I'm sure you will enjoy it for many years. Sway is a common issue with truck bed campers which can be reduced, but not eliminated. The campers are not particularly aerodynamic and the sway will…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine,…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 9

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 10

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Hey Eric, the Curt Multi-Fit Ball Kit w/ 4" Offset for Chevy/Ford/GMC/Nissan Underbed Gooseneck Hitch #C68ZV is not going to work with your Ram, unfortunately. This one is only going to work for select YMM (Year Make Model) Ford 250-450s, GMC…

view full answer...

Correct Camper Tie Downs For 8 Foot Bed 2019 Ram 3500 SRW Diesel Crew Cab

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching