Lock N Roll 5-position for 1-1/4 Inch Receiver

Question

Question:

Hi, Is there a product similar to 336VS503515 that is made for a 1-1/4inch receiver? My vehicle hitch receiver is 1-1/4inch but I need about 7inch rise. I realize I could use a 1-1/4inch to 2inch adaptor, but that would reduce the tongue weight/towing capacity. Thanks

asked by: Jason

0

Expert Reply:

Though we do not have a 5 position Lock N Roll Hitch for a 1-1/4 inch hitch, we do have The Lock N Roll Articulating Hitch w/ 3-Position Channel - 1-1/4 inch Receivers - Vehicle Side - 2.5K # 336VS503507.

This hitch has a maximum drop and rise of 4-1/4 inches. It has a maximum gross trailer weight up to 2,500 pounds and has a maximum tongue weight up to 250 pounds. It has a steel alloy construction which is strong and durable. It has a black paint finish that resists corrosion.

I attached a review video link below.

expert reply by: Noah E

0

Answer 1

Yes the Lock N Roll Articulating Hitch w/ 5-Position Channel - 2" Receivers - Vehicle Side - 11K #336VS503515 you were looking at can be used in either the rise or drop position to get your trailer level. Using the #336VS503515 in the rise…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 9

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could find…

view full answer...

Answer 12

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…

view full answer...