Crossbar Recommendation for Factory Tracks Spaced 96" Apart on Lance 850 Camper

Question

Question:

I have a Lance 850 camper I am looking for a roof rack for. It came with rails that are 96 apart. I found the previous answer, and it appears the Rhino Rack RTC/RT feet will fit, but I dont see any crossbars that appear to be long enough.

asked by: Jason P

0

Expert Reply:

It sounds like you have factory tracks on your Lance 850 camper. While you are correct that those quick mount legs # RRRLT600 or the # RLTP-2 fit the tracks, we do not have any long enough crossbars to accommodate tracks that are 96" apart. the only other solution is to purchase new tracks to mount between the ones you currently have or to remove the ones you have and bring them closer together.

For the solution for purchasing all new tracks with the crossbars, I recommend the Rhino-Rack 54" crossbar system # Y02-480B or the 59" crossbar system # Y02-490B.

If you plan on removing your current tracks and moving them closer together, the crossbars/legs without the tracks are the 54" long bars # Y02-480B-NT or the 59" bars # Y02-490B-NT. The legs that come with these kits fit your tracks perfectly.

expert reply by: Bob C

0

Answer 1

For your 2022 Lance 850 truck camper that measures 18 feet in length the best option for a cover is the Camco Ultraguard part #CAM45770 which provides the best protection in hot and dusty climates and also is easier to fit and install.

view full answer...

Answer 2

On the back side of your aluminum wheels, either on one of the spokes or near the bolt pattern, there will be a weight rating for your wheel stamped somewhere. You might have to clean it really well to be able to see it, but it will be on the reverse…

view full answer...

Answer 3

The TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear #TLA7844 is an excellent option for your camper. It will give you 4 steps up to your bumper and have a mounting bracket height of 35-3/8". This will enable you to mount it…

view full answer...

Answer 4

What I think you are asking is if the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear, #TLA7844 has a latching connection or some type of quick disconnect feature to remove from the camper. They do not have what I would call a quick…

view full answer...

Answer 5

Essentially it's how the two scissor steps store. The part #TLA7844 stores more like a traditional scissor step seen typically at the back of truck bed campers while the #TLA8004 stores more like what is seen on the side of campers. Since you…

view full answer...

Answer 6

From what you have described the TorkLift GlowStep Stow N' Go Scissor Steps, #TLA7844, will match your needs. This is for entry heights between 31" and 42". It will set within your door sill width with just under 2" on each side,…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Hey Al, this is a great question but since you have free-backing plates now you would never need to mess with the manual lock out of your Atwood coupler.

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Crossbar Recommendation for Factory Tracks Spaced 96" Apart on Lance 850 Camper

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching