Is Heat Shrink Available for a Replacement 7-Way Molded Trailer Wire Connector?

Question

Question:

I need to replace splice in a damaged trailer 7-way cable. Does your part #H20043 include shrink tubing to cover the spliced section?

asked by: George S

0

Expert Reply:

I have a solution for you but the 7-Way Molded Trailer Wire Connector, 4' Long item # H20043 does not include heat shrink to cover the spliced area. You will need the Primary Wire Heat Shrinkable Tubing - 8 to 2 Gauge - Black - 6" Long - Qty 6 item # DW05402.

expert reply by: Jerred H

0

Answer 1

You would need the heat shrink tubing for 18 to 14 gauge wire #DW05452 for trailer tail light #STL37RB. On a boat trailer I would not use crimp style connectors like butt connectors because the chance that a wire could pull out due to broken…

view full answer...

Answer 2

The CE Smith Multi Sport/Kayak Trailer #CE48810 comes with metal caps that fit onto the hub to protect the bearings from dirt/water. I went ahead and attached a photo of the caps that come with the included installation hardware. I also included a…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Chuck, since your 2024 Toyota Corolla Cross Hybrid XSE has LED taillights the correct trailer wiring harness is the part #C55ZV. Sorry for any confusion!

view full answer...

Answer 7

Definitely smart to check to get the right wiring harness, and while we can't do anything with VINs, I can tell you there are two options for 4-way harnesses on your 2023 Toyota Corolla Cross Hybrid. The difference is just if your model has LED…

view full answer...

Answer 8

The CE Smith Multi Sport Plus Boat and Kayak Trailer w/ Bunks #CE48870 that you referenced was designed to be used with boats that are up to 14 feet in length like what you have now. I attached a picture that shows the range of where the winch…

view full answer...

Answer 9

We have the CE Smith boat trailer part #CE48810 which is designed for small boats like your 12.5 foot Flycraft inflatable boat. I attached a picture that shows a similar boat loaded on this trailer as well.

view full answer...

Answer 10

The CE Smith Boat Trailer #CE48810 that you referenced is indeed rated for sustained highway speeds. It is equipped with 4.80/4.00-8 bias ply tires that feature a maximum speed rating of 65 mph, which is the standard for most trailer tires. You…

view full answer...

Answer 11

The licensing and registration paperwork is included and delivered with the CE Smith Boat Trailer, part #CE48810. The fees for licensing and registration would be paid at the time it is registered and licensed. The paperwork is not filled out at the…

view full answer...

Answer 12

The CE Smith Multi Sport Boat and Kayak Trailer w/ Bunks #CE48810 is capable of carrying a boat that is up to 12' long and weighing up to 800lbs. The winch tower can be moved front to rear to get your Stryker LX 360 to sit properly with the…

view full answer...