What is the Correct Race for Use with Bearing # L68149?

Question

Question:

Race number L68110 What is the correct bearing? I have some L68149 in stock will they work or is there a beter match for this race?

asked by: Jim

0

Expert Reply:

The # L68110 Race in my application charts works with the # L68149 bearing. We do show that the # L68149 bearing also works with the # L68111 race and this may be the application you need. The # L68149 inner bearing is paired with the # L44649 outer bearing which takes a # L44610 race. You could also order the Bearing Kit for #84 Spindle, L44649/L68149 Bearings, 10-19 Double Lip Seal, # BK2-100, if the race mentioned above is the correct part for your application. This kit includes the bearings, races, seal, cotter pin and D-ring washer.

expert reply by: Robert G

0

Answer 1

Dexter Nev-R-Lube Bearings such as the 50MM #31-71-3 referenced in your question do not have a specific maintenance or replacement schedule. These are pre-lubricated at the factory, which will make it resistant to contamination, and sealed for life…

view full answer...

Answer 2

In order to make sure you can swap to a 5 on 4-1/2 bolt pattern, you will need to pull one of your current hubs off. There are a few different bearing combinations that could have been used with your current 6 on 5-1/2 bolt pattern and it will need…

view full answer...

Answer 3

The outer bearing is part number L44649 and has a 1.063 inch inside diameter. The inner bearing is part number L68149 and has an inside diameter of 1.378 inches.

view full answer...

Answer 4

Actually it looks like your spindle had a standard zerk fitting on it at one point and it was possibly removed on purpose or accident. We don't have a way to install a new one. Honestly though you are better off without using this type of EZ lube…

view full answer...

Answer 5

The #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter #TRU74FR you were looking at has a 4 bolt mounting flange that has holes 2-7/8" apart on center, and from the outside edge of the flange to the end of the…

view full answer...

Answer 6

The distance from the end of where the inner bearing sits to the brake mounting flange is 1-1/4 inches, as shown in the provided photo. I've linked to a product description video for the spindle you inquired about.

view full answer...

Answer 7

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 8

I was able to find the seal on your trailer in my research. The seal that comes in the bearing kit #BK2-100 has different inner and outer diameters that the existing seal on your trailer. The inner and outer diameters of your seal are not common, and…

view full answer...

Answer 9

Yes, the 7-Piece Installation Set for Bearings, Races, and Seals #PTW83020 is compatible to use with Bearing #L44649.

view full answer...

Answer 10

I'd almost be willing to bet the farm that your inside bearing is actually a L44649 with an inner diameter of 1.063 inches. A typical 3500 lb axle will have a L68149 inner and a L44649 outer bearing. If that's the case, the Dexter…

view full answer...

Answer 11

We can help you with replacement seals and bearings for your boat trailer and also with replacement hubs if yours are worn or damaged. In general double-lip seals are desirable on boat trailers to help prevent entry of water and the escape of grease.…

view full answer...

Answer 12

If your races are #L44610, which they almost certainly are, you will want the following parts: Bearings: Inner bearing: #L44649 Outer bearing: #L44649 Grease seal: #10-9 Outer diameter: 1.987" Inner diameter: 1.5" Grease cap: 1.986"…

view full answer...

What is the Correct Race for Use with Bearing # L68149?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching