Inner Bearing to Brake Flange Dimension of # 84 Spindle TRU74FR
Question:
I saw the attached picture in the QandA. Could you pride the distance that I marked with the arrows? Going from the end of the thread may be a variable dimension, but the distance from the end of the inner bearing should be the same on all # 84 spindles. Thanks.
asked by: Scott F
0
Expert Reply:
The distance from the end of where the inner bearing sits to the brake mounting flange is 1-1/4 inches, as
shown in the provided photo. I've linked to a product description video for the spindle you inquired about.
expert reply by:
Mike L
0
Product Page this Question was Asked From
#84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter
- Trailer Spindles
- EZ Lube Spindle
- 1-3/4 Inch Diameter
- Round
- For 3500 lb Axle
- TruRyde
more information >
Continue Researching
- Shop: #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Kodiak 10" Hub-and-Rotor Assembly - 5 on 4-1/2 - Dacromet - 3,500 lbs
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: etrailer Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3,500 lbs
- Shop: Kodiak Ceramic Brake Pads - 3,500 lbs to 6,000 lbs
- Shop: Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Video: Kodiak Trailer Brakes K225CP Review
- Q&A: Replacement Hub/Rotor and Bearings for Tie Down Engineering TDE46245
- Video: Review of TruRyde Trailer Spindles - EZ Lube Spindle - TRU74FR
- Video: Kodiak Brake Pads Review and Installation
- Video: TruRyde Trailer Bearings Races Seals Caps - Caps - RG04-040 Review
- Q&A: Availability of Replacement Rotors and Brake Pads for Kodiak Disc Brakes
- Video: Remove, Inspect, and Reinstall Trailer Bearings, Race, and Seals Demonstration
- Q&A: Replacement Spindle and Axle Options For a 3,500LB Trailer Axle With Bent 4 Drop Spindle
- Q&A: Which is Better an EZ Lube Spindle or a Bearing Buddy Setup
- Q&A: Will EZ Lube Spindle, # TRU37FR Fit The Dexter Trailer Hub Assembly, # 8-201-9UC3-EZ
- Q&A: Replacement 3,500LB Spindle/Axle Options For Boat Trailer With Obsolete Tapered Spindle 5 on 4-1/2
- Q&A: Troubleshooting Zerk Fitting on Trailer Axle that Wont Accept Grease
- Shop: Trailer Wiring
- Video: Demco Trailer Brakes DM60124 Review
- Video: Bearing Repacking and Grease Seals Installation
- Shop: Tire Chains
- Search Results: tru74fr
- Search Results: am32156
- Shop: Front Mount Hitch
- Shop: Brake Controller
- Shop: Vehicle Tow Bar Brake System
- Search Results: ez lube cap
- Search Results: 4~35