Recommended Trailer Hitch Receiver and Wiring Harness For a 2008 Toyota Camry Hybrid
Question:
recommend type of hitch. for 2008 Camry hybrid thx
asked by: Rense M
Expert Reply:
I recommend the Curt Trailer Hitch Receiver # C12343 for your 2008 Toyota Camry hybrid. This receiver is going to be the easiest to install as it is custom fit and does not require any drilling to mount the receiver.
The T-One Vehicle Wiring Harness # 118482 will allow you to control the lights on small trailers you may tow. And these can also be used with Auxiliary Lights # C53201 if you have a hitch mounted accessory that impairs the view of your tail lights on your Camry. The Mounting Brackets # 18144 and # 18140 will allow you to secure the 4-way if you choose to run it outside of the trunk.
Curt recommends the Curt Class II Drawbar # C45521 used in the rise position with either a 1-7/8" Hitch Ball # C40001 or 2" Hitch Ball # C40018.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
No-Drill Mount for Electrical Mounting Bracket - Short
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 4 Flat
- 5 Flat
- 4 Round
- 5 Round
- Tow Ready
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-5/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- CURT
more information >
2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- CURT
more information >
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Curt Auxiliary LED Indicator Lights
- Accessories and Parts
- Hitch Bike Racks
- Hitch Cargo Carrier
- Lights
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 350 lbs TW
- 3500 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Is There a Trailer Hitch Receiver For a 2024 Volvo S60 For Carrying Bikes?
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Is A 2 Inch Trailer Hitch Available For A 2009 Toyota Camry
- Q&A: Recommended Replacement For A Furrion DV7200 RV Stereo System
- Q&A: 1-1/4" to 2" Hitch Adapter For Bike Rack On A 2011 Toyota Camry With The Draw-Tite 36416 Hitch
- Q&A: Recommended Hitch For A 2011 Toyota Camry LE V6 With Dual Exhaust
- Q&A: Where is Brake Controller Wiring on 2023 Ford Ranger
- Q&A: Recommended Brake Controller For 2018 Ford E-450 Motorhome
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Choose the Right Trailer Hitch Class
- Article: 2023 Best Gifts for Boaters & Fishing Enthusiasts
- Article: Top Gifts for Dads in 2024
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Article: What Do I Need To Tow A Trailer?