Overall Width Of Buyer Products 3371801102 Trailer Hitch

Question

Question:

I need to know the overall width of this hitch. Metal plates have been welded to my frame rails which now limit a max hitch width to 42 3/8 Thank you!

asked by: Ben

0

Expert Reply:

Per the manufacturer, The Buyers Product Hitch # 3371801102 overall width from mounting hole to mounting hole is 38-3/8 inches across from center on center. Then on each side starting with the hole that's towards the rear of the vehicle will measure 3-11/16 inches from the first to the center hole and 6-7/16 inches from first to the last hole.

expert reply by: Noah E

0

Dimensions of Buyers Product Hitch
(click to enlarge)

Answer 1

Ths shorter school buses are built on van cutaway chassis. So since your bus is built on a 2002 GMC Savana Cutaway chassis the Buyers Products hitch part #3371801102 that you referenced would fit and work well.

view full answer...

Answer 2

The etrailer.com Trailer Hitch #E98861 will fit your 1997 GMC Savana so long as it is a cargo or passenger van model; if you take a look at the photo of the dimensions of this hitch you can see that the bolt holes are also 40" apart like…

view full answer...

Answer 3

The only trailer hitch available or a 2020 Chevrolet Express Van Shuttle Bus is the Buyers Products 2" Hitch Receiver part #3371801102. The Buyers Products 2" Hitch Receiver does require drilling but there is no other option for…

view full answer...

Answer 4

The Ultra Frame Trailer Hitch Receiver #41947 has an adjustable cross-tube that allows the receiver to be moved into a variety of height adjustments. There are 3 locations on that this hitch can be mounted in (see attached photo diagram): Height from…

view full answer...

Answer 5

I went out to our warehouse and measured the Buyer's Products hitch, part #3371801102, and it's 6-1/2 inches from the top of the mounting surface to the top of the reciver tube. Then it's about 9-1/2 inches to the bottom of the receiver…

view full answer...

Answer 6

On the Buyers Products hitch, part #3371801102, the mounting holes are 38-3/8 inches across center on center. Then on each side starting with the hole that's towards the rear of the vehicle they measure 3-11/16 inches from the first to the center…

view full answer...

Answer 7

I would be happy to help you with dimensions to the Buyers Products 2" Hitch Receiver For GM Express/Savana with Cutaway Chassis item #3371801102 you were looking at. The measurement you are asking about is 9-1/2". This is from the top of…

view full answer...

Answer 8

The Draw-Tite Ultra Frame Trailer Hitch Receiver w/ Cast Center - Custom Fit - Class V - 2" #41946 is a confirmed fit for your 2005 Chevy Express van but the measurements are correct. This hitch does require drilling to install rounding out the…

view full answer...

Answer 9

To use a hitch to tow with your 2003 Chevy Express van, it needs to mount to the frame at the rear underside of the vehicle to provide the necessary stability. If holes are not already there to install the hitch to you can look at a custom option…

view full answer...

Answer 10

We have a Class IV hitch that fits your 2006 Ford E-450 with the Draw Tite part #41947 but the #14090 would not fit.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Overall Width Of Buyer Products 3371801102 Trailer Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching