Replacement Q Tower Pads for 2008 and 2010 Toyota Prius

Question

Question:

Hi, previous we owned a 2008 Prius and I found this answer from your colleague Keg G - The replacement pads for your Q Towers on your 2008 Toyota Prius are # Y8810084 and # Y8810097. Wanting to check which one of these is rear and which is front in this configuration. We now own a 2010 Prius I found this answer from Mike L - The roof rack on your 2010 Prius uses the A pads, part # Y8810084 under the rear two towers and the E pads, part # Y8810082 under the front two towers. The pads are sold individually. It appears I can use part of my pads from 2008 Prius, but dont know which part mentioned above is rear or front. Long time ago I thought I read somewhere that the ....0084 part might be front for 2008 which then I might switch to rear for 2010 prius as mentioned above. Want to check before I place order for E pads part #Y8810082 if I already have the correct Y88810084 and which order it fits under 2008 Prius so I switch it correctly.

asked by: Luyen

0

Expert Reply:

Thank you for all of the info! It looks like you are correct in what you're looking at. Below are the Q Clip numbers for each Prius as well as the corresponding pads that go with the Q Clips.

Your 2008 Toyota Prius used these Q Clips:
Front - Q5 Clip - "A" Pad # Y8810084
Rear - Q124 Clip - "F" Pad # Y8810097

Your 2010 Toyota Prius used these Q Clips:
Front - Q99 Clip - "E" Pad Y8810082
Rear - Q5 Clip - "A" Pad Y8810084

Hope this helps!

expert reply by: Jon G

0

Answer 1

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 2

Some wobble is unavoidable with bike racks like the Saris Superclamp #SA4025F. To help limit the wobble, you can use this anti rattle #C27UR. I've used it and it works really well especially for vertical movement. If you haven't…

view full answer...

Answer 3

On your Yakima Hold-Up Bike Rack #Y02445 and others with an anti-rattle feature the anti-rattle device in the shank applies pressure to push the rack's shank against the inside of the hitch receiver tube. This pressure can cause some slight…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Replacement Q Tower Pads for 2008 and 2010 Toyota Prius

Continue Researching