Clamps For Extang Trifecta Tonneau Cover on 2021 Nissan Titan With Utili-Track

Question

Question:

Will this this work for the utilitrack track system for nissan titan EX2244-0204

asked by: Tommy B

0

Expert Reply:

We do indeed have replacement clamps for an Extang Trifecta tonneau cover for a 2021 Nissan Titan; the correct clamps are the following part number:

- Replacement Clamps for Extang Trifecta Soft Tonneau Covers # EX2244-0204

expert reply by: Kyle S

0

Answer 1

The Replacement Clamps for Extang Trifecta Soft Tonneau Covers #EX2244-0204 will indeed fit the factory track system on a 2021 Nissan Frontier. While this may work, it is not technically designed for your Tonno Pro hard fold #TPHF-452. We do not…

view full answer...

Answer 2

IF you're finding that the clamps #EX2244-0204 are too small and don't fit the bed rails on your vehicle, you can trim the plastic to get the clamp to fit. I've attached a snippet from the installation instructions showing Extang giving…

view full answer...

Answer 3

Yes, the adapter clamps that are used to secure the Extang Trifecta 2.0 Tonneau Cover #EX92985 to the Utili Track on your 2018 Nissan Frontier can be found with part #EX2244-0204. This includes all 4 clamps needed for installation. If you can tell me…

view full answer...

Answer 4

Since you are missing the bed rail clamps of your Extang Trifecta the correct replacements would be the part #EX2244-0204 that you referenced.

view full answer...

Answer 5

Yes, we sell both of the parts you are looking for in the attached photo. These two parts are the Replacement Clamps for Extang Trifecta Soft Tonneau Covers part #EX2244-0204 and the Replacement Tail Clamp Assembly for Extang Trifecta 2.0 Tonneau…

view full answer...

Answer 6

Yes, the Replacement Cab Clamp Assembly part #EX1034 is a fit for a Extang Trifecta 2.0 Soft Tonneau Cover. In regards to installation, you'll need to disconnect the screws from the crossbow of the cover so that it will drop down and the cab…

view full answer...

Answer 7

None of the methods are super easy. I'd recommend three though you have to remove hinges. This is least invasive, doesn't require cutting the cover, and also doesn't risk damaging cover.

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Clamps For Extang Trifecta Tonneau Cover on 2021 Nissan Titan With Utili-Track

Product Page this Question was Asked From

Continue Researching