Pop-Up Camper Latch and Catch Measurement

Question

Question:

What is the range of distance between the screw holes on each part?

asked by: Logan

0

Expert Reply:

The Pop-Up Camper Latch and Catch, # 37211845 has an adjustment range of about 1/2". From the bottom fastener holes on the main body of latch assembly to the fastener holes of the catch, is approximately 5-1/4".

expert reply by: Michael R

0

Answer 1

For pop-up camper latches we have the: - Pop-Up Camper Latch and Catch #37211845 (black) - Pop-Up Camper Latch and Catch #37210845 (white) - Pop-Up Camper Latch and Catch #37210825 (zinc) These are the only pop-up camper latches that we carry. They…

view full answer...

Answer 2

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to…

view full answer...

Answer 3

I may have a solution for you but I'm not aware of a bolt on safety chain bracket or clevis that can be used. However you can simply take a safety chain set (or your existing chains) like the 42" Long Safety Chain with 3/8"…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to…

view full answer...

Answer 6

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 7

I spoke with my contact at Pollak and he stated that the Pollak Replacement 7-Pole, RV-Style Trailer Connector Socket, #PK11893-11933 is the correct replacement part for the Pollak PA66-MD40 that you have.

view full answer...

Answer 8

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 9

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

If you have already added the fuse and the trailer charge circuit is not activated in the 2019 Ford F-350 Super Duty with factory integrated brake controller, then you want to make sure the trailer is connected and you press the brake according to…

view full answer...

Answer 12

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and…

view full answer...

Pop-Up Camper Latch and Catch Measurement

Product Page this Question was Asked From

Continue Researching