Replacement Fan Motor and Blade For Philips Industries Ventline V2062 Fan In Mobile Home

Question

Question:

Philips model V2062. No clue to age of mobile home, but I need everything . A million thanks for the help!

asked by: Pamela S

0

Expert Reply:

Your Philips model V2062 is the same as the Ventline V2062 as Ventline was a division of Philips before they were bought by Dexter. We do have the Replacement 110-Volt AC Fan Motor # BCD0314-00 and Blade # BVA0312-00 that will fit your fan.

expert reply by: Bud M

0

Answer 1

Yes, the Phillips V2062 and the Ventline V2062 are the same so for a replacement motor you'd need #BCD0314-00. For the replacement fan blades you will need part #BVA0312-00.

view full answer...

Answer 2

The correct replacement motor for your Ventline V2065 fan is indeed part #BCD0390-00 and the proper replacement fan blade is part #BVA0312-00. The replacement blade is 6-1/2 inches in diameter, which is what the 6.5 on your existing blade means.…

view full answer...

Answer 3

The Ventline V2044 Bathroom Ceiling Vent can use the Replacement 110-Volt AC Fan Motor for Ventline RV Bathroom Insert Fan w/100 CFM Capacity #BCD0314-00 or the Replacement Fan Motor for Ventline Exhaust Fan #BCD0390-00. We have confirmed with…

view full answer...

Answer 4

The V2044 fan has been discontinued for awhile, but the Ventline #BCD0390-00 would be the correct 110V-AC motor. I've confirmed that these are the proper replacements with my Ventline representative. For the fan blade the replacement for the…

view full answer...

Answer 5

When installing the Replacement Fan Blade for Ventline Bathroom Ceiling Vents #BVA0312-00, you will simply need to press it onto the motor shaft. This is not threaded as the fan would end up spinning off said shaft, but there are vertical grooves…

view full answer...

Answer 6

The replacement motor you need for a Ventline roof vent V2062 is the part #BCD0314-00 and for the fan blade part #BVA0312-00.

view full answer...

Answer 7

There is not a specific kit that comes with the motor, blade, and ceiling vent cover for your exhaust fan V2062 so you will want to get those separately. You can go with Replacement 110-Volt AC Fan Motor #BCD0314-00 and Replacement Fan Blade for…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...