Where Does Stoplight Circuit for Redarc Tow Pro Elite Need to Come From

Question

Question:

truck has round not blade 7 way. so considering this spliced into i guess brake light. or the autowtow unit. I also have a hayes sway control unit that I may like to used in combination

asked by: Geoffrey C

0

Expert Reply:

On 7-way trailer wiring there isn't a dedicated stoplight circuit so you won't be able to get that circuit for the Redarc Tow Pro # RED44FR from there. You'd need to get it from the brake pedal light switch or a third brake light.

expert reply by: Jameson C

0

Answer 1

The best solution for your application is to install the Tekonsha T-One #118405 on your 2009 Toyota FJ Cruiser for your standard trailer lights and then add the Wiring Kit #ETBC7L which comes with everything you need to convert the 4-Way to a…

view full answer...

Answer 2

To convert your 4-way to a 7-way so that you can install a brake controller in your 2013 Toyota FJ Cruiser will require the kit part #ETBC7. For a brake controller I would recommend the Prodigy P3 Brake Controller part #90195. This is our best…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 9

Sure thing, I will go ahead and list out what you need for your 2023 Kia Sportage to add a 7-way for a brake controller so you can tow with the Curt Trailer Hitch Receiver #C94WR: - T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer Connector…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 12

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Where Does Stoplight Circuit for Redarc Tow Pro Elite Need to Come From

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching