Replacement Anchor Plates For A Yakima Bar System

Question

Question:

Will this fit regular and Yakima HD track systems

asked by: Hugo A

0

Expert Reply:

When it comes to replacement Anchor Plates # Y8810074 it replaces the 8 threaded anchor plates for the Yakima LandingPad 1 # Y00221 which works with the Yakima SkyLine and Control Towers. Per Yakima It will not fit the Yakima HD bars.

expert reply by: Noah E

0

Answer 1

The Replacement Frame Bolt for Yakima Rack and Roll Trailers - Qty 4 #Y8880183 is not a fit for your Rhino Rack RS 2500 slots. Those bolts are designed for the trailer frame rails and not aero crossbars. You instead will want bolts like the Aero…

view full answer...

Answer 2

The thickness of the T-bolt head of the part #Y8880184 you referenced is 5/32 of an inch. I attached a picture that has all of the other dimensions as well. These T-bolts are M10 x 1.5 x 25

view full answer...

Answer 3

Yes, the Replacement Anchor Plate "A" for Yakima LandingPad 1 #Y8810074 is the same anchor plate that is in the Replacement Hardware Bag for Yakima LandingPad 1 #Y8890028. For the bolts #Y8890028 does come with 4 of the corresponding M6 x…

view full answer...

Answer 4

The Yakima Replacement Anchor Plate Style-A, Part #Y8810074, comes as a set of 8 plates that measure 3/4-inch x 7/8-inch. The centered threaded hole measures 0.2 inches (or 5.1 millimeters) in diameter. Please refer to the photo provided. The Yakima…

view full answer...

Answer 5

If you have the Yakima Skyline or Control Towers then you can use the Landing Pad 1 for Yakima SkyLine and Control Towers part #Y00221 to mount them into tracks/channels like those found on select Retrax Tonneau Covers.

view full answer...

Answer 6

The Yakima Replacement T-Bolt with Nut for Yakima Rack and Roll Trailers - Qty 4 #Y8880184 will fit in the channels of your HD bars, but for the most part, crossbar mounted accessories will come with (or have available) T-channel hardware that will…

view full answer...

Answer 7

The Yakima HD bars you were looking at has a slot that measures 11mm (7/16") wide on top, 8mm(5/16") deep, and 22mm(14/16") wide at it's bottom. As long as the Eye bolts you get work with this size slot, then then you won't…

view full answer...

Answer 8

The Yakima SkyBox 16 Roof Cargo Box is compatible with bars measuring up to 1-11/16" tall x 3-1/2" wide. The Yakima HD Crossbars like part #Y01159 measure 1-1/2" tall x 3" wide so they will be a fit for this cargo box. I…

view full answer...

Answer 9

I recommend picking up the Aero Style Crossbar T-Slot Fit Kit #MPG8287 which comes with bolts, nuts, and washers that will fit in the Yakima HD Bar T-Slots like the 78" part #Y01159. If you're trying to find specific dimensions for your own…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Anchor Plates For A Yakima Bar System

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching