Custom Fit Roof Rack Kit With Y00221 | Y00430 | Y53TR
(127 reviews)
Price: $688.80
Custom Fit Roof Rack Kit With Y00221 | Y00430 | Y53TR
Item # Y59WB
Our Price: $688.80
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
- All Info
- Reviews (127)
- Q & A (0)
- Videos (16)
- Photos
Yakima Roof Rack - Y59WB
- Crossbars
- Aero Bars
- 2 Bars
- 70 Inch Bar Space
- Yakima
- Silver
- Overhang
Extremely quiet, aerodynamic crossbars attach to Yakima towers to create a stylish roof rack for your vehicle. Rubber strips in T-slots push down to load carriers or accessories - no need to trim. Full-length aluminum bars maximize carrying capacity.
Features:
Yakima 70" JetStream LG - Silver:- Quiet, low-profile crossbars let you build an aftermarket roof rack for your vehicle
- Pair with Yakima towers and a fit kit (sold separately) to create a complete roof rack
- Asymmetrical JetFlow shape creates an extremely aerodynamic roof rack system
- Built-in WindRidges help control air flow over bars to dramatically reduce wind noise and vibration
- Aero-style bars reduce drag to help maintain fuel efficiency
- Full-length design maximizes space for carriers and accessories
- Versatile crossbars accommodate accessories that mount in the T-slots or clamp around the bars
- Works with most universal-mount bike, water, snow, and cargo carriers
- Rubber SmartFill strips in T-slots allow for easy installation of channel-mounted accessories
- Simply push down on the SmartFill strips to slide in accessories - no trimming required
- Bottom channels allow for easy installation on Yakima towers
- Fit BaseLine, RidgeLine, SkyLine, and TimberLine towers (sold separately)
- Etched measurements on bottoms of bars help center rack on your roof
- Lightweight aluminum bars are durable and rustproof
- Internal JetTruss extrusions provide exceptional bar strength
- Clear anodized alloy finish is corrosion resistant
Yakima Landing Pad 1 (Set of 2):
- Provide mounting point for Yakima SkyLine and Control Towers
- Fit vehicles with C-shaped factory rack tracks
- Attach to factory tracks with anchor plates and screws
- Include snap-on covers for protection when Towers are not in place
Yakima SkyLine Towers (4-pack) (w/new covers):
- 4 Heavy-duty towers mount Yakima crossbars to your vehicle with fixed mounting points, flush side rails, or tracks
- Pair with 2 Yakima crossbars and Landing Pads (sold separately) to create a complete roof rack
- Tower pitch can be adjusted 6 degrees forward and 6 degrees backward to level your crossbars
- Versatile BarBeds are curved to accommodate the elliptical shape of Yakima CoreBar and JetStream crossbars
- Also fit RoundBar crossbars with adapter (Y03536 - sold separately)
- Easy, tool-free installation - just drop tower onto Landing Pad and close the cover
- Included torque tool clicks 3 times when crossbar is tightened to tower - eliminates fear of under- or over-tightening
- Lockable with Yakima Same Key System (SKS) lock cores (Y07204 - sold separately)
- Weather-resistant die-cast aluminum, stainless steel, glass-reinforced plastic, and elastomer construction
8000221 Landing Pad 1 for Yakima Control or Sky Line Towers
8000430 Yakima Jet Stream Cross Bars - Aluminum - 70" Long - Qty 2 - Silver
8000163 Yakima Timber Line Roof Rack Towers for CoreBar, JetStream, and RoundBar Cross Bars - Raised Side Rails - Qty 2
Replaces 8000148
Video of Custom Fit Roof Rack Kit With Y00221 | Y00430 | Y53TR
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Yakima Crossbars SkyLine Towers Review
Hey everyone, it's Evangeline here at etrailer and today we'll be taking a look at our Yakima SkyLine towers. These are designed for your fixed mounting points, your flush rails, or your track systems. So if the roof of your vehicle looks like this, you probably need these. If you wanna carry around roof mounted accessories like kayaks or ladders or maybe you need to bring a Christmas tree home, you first need a roof rack system. Now this is gonna be the Yakima SkyLine towers for those vehicles that specifically require a custom fit kit for their fixed mounting points. Now if your vehicle does not look like this you might have a naked roof or raised rails.
That's why it's very important before anything to use our fit guide here at etrailer.com. Put your year, make model and then find the right fit for you. And if this is one of them let's take a look at how it works. Etrailer.com also helps you get the full kit for your vehicle because the skyline towers don't work alone you also need the appropriate crossbars as well as the correct fit kit or landing pads for you. But with this, you get a low profile roof rack so it doesn't stick too high up.
You get a heavy duty weight capacity since this is an aluminum roof rack. So usually they have 165 pounds capacity, depends on the vehicle, and you have this very sturdy but also very custom fit kit for your vehicle. That way, no matter what you put on it within reason and wherever you go, you know it's gonna stay there. But my favorite feature about this roof rack is the door design. So you pinch on the door to open it and that's it.
Just like that, you can lift the whole roof rack off of your roof. When you need to install it, you just pop it right back on. So the height of the tower is about 3 1/2" from your fixed mounting point to the top of the tower. The actual height can change depending on what crossbars you have and what rails you have, but compared to a lot of the other flush mounted crossbars and roof racks, it's just very low to the roof. Now with this style of a rack though, you are limited to the fixed mounting points or the flush rails of your vehicle.
So wherever they are, that's how much crossbar spread you get. For example, ours is set to 28" apart. On the other hand, if you have an aggressive tilt to your roof, you can actually adjust this up to six degrees forward or six degrees backward to help even out the playing field. Now I like to leave my roof rack on my vehicle and Yakima is pretty known for its durability. So the SkyLine towers are made of glass reinforced plastic, aluminum, stainless steel and elastomer. So all that is combined to help them stay strong even if you leave them on all day, all year. But if you do need to take off your roof rack you also have a feature to make it more low profile. Start by flipping both doors open and then you can lift the roof rack up and off of your roof. This way you can store it inside of your garage or in your house. You can leave your base on your roof rails. All you need to do is cover them with the included cover and that's it. You're done. The covered bases sit about 2" high up off of your fixed mounting point and makes for a much more low profile look. Your towers will have everything you need to install them which really is just one tool. And your fit kit has the hardware needed to undo the factory mounting points on your vehicle or for your track system if that's what you have. Now, that install process is extremely simple. Let's take a look at it. So these are what your towers look like when they are not on your roof. So they come all assembled in the box. All you need to do is get the appropriate landing pads for your vehicle. These landing pads can look different depending on your car and that's why it's very important to use our fit guide to get the right fit for you. You have four towers as well as the torque tool. And depending on your crossbars, you will also get a separate adapter to be used with those specific bars. With your landing pad kits, you'll get a part that fits your specific vehicle. You will get the hardware needed to install that part and you will have the base as well as the base cover. So if the towers are not on your vehicle you could just cover that base pad and take the cover off to install the tower. Here's an example of how the landing pad can be used depending on your cars. So you have a factory mounting point in this specific flush rail. So the pad goes over that hole and then you're gonna get your base which goes on top of that pad. And then you have a bolt with split washer and flat washer which is used to tighten down those two pieces to your car. The torque tool for your towers comes in handy whenever you're tightening down those bolts because it has a setting for tension. Once you get enough tension, it automatically clicks and prevents you from over tightening. Now to set up your tower for your crossbars there's different adaptor pieces. We're using the one for the JetStream crossbars. So we start by pushing in this plate into the tower. So you are gonna hear some clicks and that's how you know it's secure. Now we're gonna open up the tower door. So this involves pinching the door and pulling. Be careful because if you slide your fingers forward it doesn't feel as good. But with the door open, you can then loosen this bolt up front. It says to do it eight times. I just go until the bolt underneath is visible so you can see underneath what I mean. Notice how you have this little bolt head hiding around. You're gonna try to get at it with the tool. You can see how I do have access. That means as we flip this tower back over I can put this plate up top and then I can tighten down and thread onto that plate. With adapter and plate, this can now slide into your crossbar. For other adapters, they're designed to slide over or around your crossbar. With this specific style, I do recommend for the initial slide making sure that this is loose, but after that even if you have it fully tightened down you'll still be able to slowly adjust it on the crossbar. So with the towers on you're then ready to put this onto your roof. Now what I do is I just kind of roughly measure how far apart our landing pads are and that's when I can measure on the towers the distance apart they roughly need to be, in my case, 43 1/2. You could be off by 1/2" or so 'cause you can still move them. Also, supposedly this is when you put the rubber pieces inside of your crossbars. I do that after I've already installed them onto the roof. I take them back off and then I push them in so that I know exactly where the towers will be sitting. Make sure your towers are torqued down at their bottom bolt. Do that for both sides before installing. This is a lot easier with a friend on the other side but still doable with one person. So leave those doors open so that you can gently place them onto your roof. The bottom bracket with the door open fits onto your base so see how that just pushes into place. And then to secure it, just push that door close and you've got a sturdy fit. If you're using Yakima same key system lock cores, this is a time to switch them out on your towers. But other than that, just double check that all the towers are strong and secure and everything is sturdy. And that's it for the install of your roof rack. That right there was a look at the Yakima SkyLine towers for your Yakima crossbars for when you have vehicles that have fixed mounting points, flush rails or track systems.
Customer Reviews
Custom Fit Roof Rack Kit With Y00221 | Y00430 | Y53TR - Y59WB
Average Customer Rating: 4.9 out of 5 stars (127 Customer Reviews)
Extremely quiet, aerodynamic crossbars attach to Yakima towers to create a stylish roof rack for your vehicle. Rubber strips in T-slots push down to load carriers or accessories - no need to trim. Full-length aluminum bars maximize carrying capacity.by: Eric 05/13/2024
Fit our Subaru Forester perfectly. Install was a breeze. For the money I wish they came with the core locks.
by: John11/16/2023
Very nice quality towers. Very heavy duty! They have a cool "snap" on / off mechanism for quick removal and installation.
by: Frank P.03/06/2016
Fit good with the OE track on roof. I like the new covers they supplied with the mounts.
by: Bryan03/27/2024
Very nice and heavy duty. They don’t look too fragile on a lifted truck with oversized tires.
by: Rob04/19/2023
Honestly, I love etrailer. I love the expert help that you all provide. It's clear by the 1 year follow-ups that you care more about the relationships with your customers then just making a sale. Your service is friendly, informative and fast. I always come here first to look for my next purchase. Thanks again-Rob.
by: William02/28/2024
You guys provide great products and excellent customer service.
Thanks
by: Layne 02/11/2024
These crossbars were easy to install and adjust. Be sure to get all the pieces you need. There is no mention of the Landing Pads necessary to use these.
by: Aaron 02/10/2024
Perfect match
by: Pat G08/29/2013
Great first experience dealing with you guys! Shipped fast, and was a faster install. You gave me the right parts and it went together in a flash.
Will definitely be doing business with you all again.
by: William 01/11/2024
Shipment received, as ordered! Thanks again to Bryce D., for assistance.
by: Nelson06/26/2023
Ford
It was what it was advertised and fit perfectly on my 2023 Ford Maverick
by: Dan 11/06/2023
Great company! Fast delivery.
by: Jerry 07/29/2023
I have ordered several times from Etrailer and have always received efficient, timely and reasonable shipped items. Did not use customer service with this order but it has always been good.
by: Ric 07/22/2023
Honestly went back to etrailer after buying something i couldnt find on the big A before because their support was so good and delivery speed was soo fast.
by: Doug02/16/2022
First trip with the new rail system and it looks like it worked out just fine. Thanks to both of you and Kimberly for all of your help and follow up I do appreciate it.
by: See11/03/2022
with so many variables having someone that could sort through all them was very helpful Thanks etrailer
by: Philip 05/29/2023
These really look so much better then the factory racks! Easy to install. Easy to order! Great product!
by: Hogan06/09/2023
I’ve placed 2 separate orders with etrailer in the last 6 weeks. Their service, response, pricing and follow-through have been terrific each time. I will use them every chance I get.
by: John02/18/2022
These will mount to the rhino rack tracks so I could use my Yakima control towers and rack.
by: Luke 07/24/2023
Works as described
by: Earthdog Mom05/11/2023
Quality product, timely shipping, transported with care. Packaging received fully intact with no damage.
Thank you etrailer for yet another great ordering experience!
by: Dennis08/15/2019
1996 Ford Explorer
Om my 1996 Ford Explorer, after the plastic factory cross bars failed, I was able to use the etrailer web site and tech support to determine that landing pads were available that fit the factory track and would allow me to use my Yakima towers and round bars. This was a great fix!
by: Matt08/17/2020
This company is great! I was looking everywhere for a set of crossbars that would fit my pop up camper. After not being satisfied with the options I called the customer service line and spoke with Crystal. She was great at recommending which parts would work on my camper. I had a lot of questions and she answered them all. If she didn't know the answer she found out for me. I installed my new crossbars on my camper this afternoon and they fit perfectly! They're solid as a rock! I'm so excited to use them!
by: Greg05/18/2011
Was very pleased with the Yakima racks and installation was a snap! First time customer of etrailer and was elated with whole experience! Shipping was lighting fast too!!! Will do business again...
by: Michael01/22/2023
Yakima SkyLine Towers are well-designed and well-executed. They easily fit into the Yakima Landing Pads and form a tight fit when closed. And they also fit nicely into the Yakima JetStream Crossbars when following the Yakima instruction manual and various YouTube videos. I did run into a snag at first where I found the rubber seal on one SkyLine Tower getting caught on the JetStream Crossbar track, but after that I was careful not to let that happen with the other towers.
I find the appearance of the Yakima SkyLine Towers to match their level of quality in materials and design.
25
645
Show More Reviews
See what our Experts say about this Yakima Roof Rack
- Will Rhino-Rack Crossbars Fit On Yakima BaseLine Towers? The top channel on most crossbars like the Rhino-Rack and Yakima are similar but you should never mix and match towers and crossbars between different manufacturers. Their components are designed to work specifically with each other and your Yakima towers may not work properly with the Rhino-Rack crossbars. Instead you will want to stay with the Yakima crossbars from the list below to ensure they fit together properly and you have a manufacturer who will stand behind the warranty for the...
view full answer... - What Are the Dimensions of the Yakima BaseLine Towers With the Crossbars and BaseClipKason, the BaseLine Towers for Yakima Crossbars # Y28TR (4") paired with the BaseClip Fit Kit # Y27FR & # Y06124 (1"), and the Yakima JetStream Crossbars # Y00430 will leave you with approximately 6 1/2" from the top of crossbar to the top of your roof. You can take an inch and an eighth off that to get the measurement from roof to the bottom of the crossbar so that'd be 5 3/8".
view full answer... - Which Yakima Landing Pads for 2021 Toyota Highlander to Mount Skyline TowersTo use the Yakima Skyline Towers # Y53TR on your 2021 Toyota Highlander the correct landing pads are the Landing Pad 28 for Skyline and Control Towers # Y66VR.
view full answer... - Roof Rack Recommendation for 2020 Honda PilotThe rack you need will depend on how the roof of your 2020 Pilot is fitted out. I really like the Yakima JetStream roof rack, because of how well they're built and designed. They may not be the least expensive option, but they work very well and are extremely durable which makes them the most popular choice for your vehicle. If you have a bare roof, you'll need the following parts: • Yakima 60 inch JetStream crossbars, part # Y00426 • Yakima BaseLine roof rack towers, part # Y28TR •...
view full answer... - Recommended Roof Rack For A 2023 Toyota RAV4 With A Thule Hullavator Hi Cathy, To ensure that you can get the extra extension to mount the Thule Hullavator # TH898 you'll want to go with a Yakima roof rack system. Yakima crossbars run their mounting track the entire length of the crossbar so you can go with ones that are longer than your typical length without worrying if the mounting feet will be able to connect. You'll want the following components: Yakima JetStream Crossbars - Black - 60" Long # Y00426 or silver # Y00429 SkyLine Towers for Yakima Crossbars...
view full answer... - How to Determine if Two Malone SeaWing Kayak Carriers Fit 2019 Subaru Outback Factory Roof RackYour kayaks will fit the Malone SeaWing Kayak Carrier with Tie-Downs # MPG107MD, but two of them will not fit your 2019 Subaru Outback's factory roof rack because the crossbars simply are not long enough for both the carriers and your 30" wide kayaks. So to use a kayak carrier you'll need an aftermarket roof rack, and the verified fit to replace the roof rack on your 2019 Outback is from Yakima, and consists of the following part numbers: - Yakima JetStream Crossbars - Silver # Y00428...
view full answer... - What Roof Rack Can I Use with the Thule Hullavator on My 2022 Toyota Highlander with Flush Rails?I have a great solution for your flush rails on your 2022 Toyota Highlander to use the Hullavator # TH898. Yakima temporarily discontinued the Y00148 because they are updating the feet to fit a wider range of vehicles. Yakima has been changing a lot of fitments lately because of this factor. The landing pads # Y66VR are separate from the Y00148. However, with that being said, Yakima does have a roof rack system that fits your flush rails with a different model of feet. For that system,...
view full answer... - Best Roof Rack for 2020 Kia Soul with Fixed Mounting PointsThe best roof rack for your 2020 Kia Soul with a naked roof (fixed mounting points) is from Yakima because it will give your Kia a roof rack that combines effectiveness and style while minimizing any wind noise that can occur with lesser roof racks. This roof rack is made up of: - Yakima JetStream Crossbars # Y00425 - SkyLine Towers for Yakima Crossbars # Y53TR - Landing Pad 22 # Y00248 - Same Key System Lock Cores (Optional) # Y07204 This roof rack will look stellar atop your 2020 Kia...
view full answer... - Yakima Roof Rack for 2022 Subaru LegacyYou are on point with Yakima being a really high-quality product so I completely understand wanting to stick with them for a roof rack on your 2022 Subaru Legacy. The Yakima roof rack that fits your Legacy consists of the following parts: - Yakima JetStream Crossbars # Y00425 - SkyLine Towers for Yakima Crossbars # Y53TR - Landing Pad 22 for Yakima Towers # Y00248 - Same Key System Lock Cores (Optional) # Y07204 I have added links to video reviews for you to check out as well.
view full answer... - Recommended Roof Rack for Mounting a Thule Hullavator Pro on a 2021 Toyota RAV4The Thule Hullavator Pro, part # TH898, does in fact need crossbars that extend 4" - 8" beyond the feet. To use the flush rails on your 2021 Toyota RAV4, you will need a roof rack that has feet that are compatible with the rails. With those two stipulations in mind, the Thule WingBar Evos don't look like they will provide enough clearance with their 47" of crossbar length. Instead, I recommend the Yakima HD Crossbars, part # Y01156. They are 55" long, so they will have the extension you...
view full answer... - Yakima Roof Rack Parts Needed for a 2017 Subaru Outback WagonYes, the recommended Yakima Landing pad for the 2017 Subaru Outback is the Landing Pad 15 part # Y00241 that you referenced. For crossbars you would want the part # Y00408, for towers part # Y53TR and adapters part # Y03536. All of these components would complete a roof rack for your vehicle.
view full answer... - 2010 Outback Roof Rack OptionsAdding feet to your 2010 Subaru Outback Wagon will not change the weight limit of the rack. The maximum weight limit will still be 165lbs. Adding the Rhino-Rack RT-Style Roof Rack Tracks - Rivet Mount - 51" Long - Qty 2, part # RRRTS551, does not change that. In fact, adding an extra feet/legs and crossbars to your roof rack will actually lower the weight you can carry on your roof. That is because your roof rack's weight actually counts toward the 165lb weight total. I would use my existing...
view full answer... - Roof Rack that Can Fit 2023 Jeep Wrangler Rubicon with Sky One Touch RoofThe Yakima Jetstream roof rack part numbers # Y00428, # Y53TR, # Y00226 is a fit for your 2023 Jeep Wrangler Rubicon that has the sky one touch roof and would do a great job to carry a tent and other cargo.
view full answer... - Roof Rack & Attachments For 2010 Toyota Tacoma TRD SR5I would get the Yakima HD Bar Roof Rack System. You'll need the HD bars # Y01156 Skyline Towers # Y53TR HD bar adapter # Y03541 and landing pad # Y74FR. You can then use the JayLow Kayak Carrier # Y04073, Off-Grid Cargo Basket # Y07139 or Skybox Cargo Box # Y95AV. These are just my suggestions for accessories but there is much much more on our website if you're wanting something different!
view full answer... - Will the Rhino-Rack # Y01-130B Fit My 2022 Hyundai Santa Cruz?Yes, you will be able to put 2 bikes on the Rhino-Rack Heavy-Duty Bar Roof Rack for Camper Shells - Track Mount # Y01-130B if the combined weight of the racks and bikes is exactly 220 pounds (or under). As far as the fitment of the # Y01-130B on your 2022 Hyundai Santa Cruz, that is a bit more complicated. The tracks will fit with the included hardware with drilling. With the 63" tracks, you can cut the tracks to the size of the bed rails. The complicated part is the crossbar fitment....
view full answer... - Can Yakima LockNLoad Platform For 2017 Toyota Highlander XLE be Used with Roof TentThe Yakima LockNLoad Platform part # Y05045, # Y53TR, # Y05042-2, and # Y00242 would work great for your tent setup. This will give you a 165 lb dynamic weight capacity which is the standard capacity needed for tents which would use a static capacity instead and would be much higher. This is a creative solution to give you the additional spread you'd need for your tent too!
view full answer... - Best Roof Rack for a 2015 Mazda 3 5-door with Fixed Mounting PointsFor the 2015 Mazda 3, you'll only have access to either Yakima or Rhino Rack roof bars. Both are great companies and there's a few differences that are important to note about the two companies. Rhino Rack doesn't produce as many accessories, but is a smaller than average bar and fits more mounting hardware in both its C-Channel and around the bar. Additionally, its locking system is two part, one for the foot pack and one for the c-channel accessories as a separate part. Finally, Rhino...
view full answer... - Parts To Use Existing Yakima Aero bars With RetraxONE For Toyota TacomaIt is possible to use your Yakima Aero bars on the RetraxONE part # RTT-60851 for the 2017 Toyota Tacoma. You need 2 sets of landing pads part # Y00221 to slide into the tracks of the Retrax system. You need one set (quantity of 4) of Yakima Skyline Towers part # Y53TR to attach to the landing pads. Then the Aero bars mount to the towers.
view full answer... - Roof Rack Recommendation for Rhino Rack Sunseeker II Awning on 2017 Ram ProMaster CitySince the Sunseeker II Awning Item # RR32105 only fits Rhino-Rack Heavy-Duty, Aero and Sportz crossbars; Thule and Inno square crossbars; Yakima round crossbars we have a solution, but it's not the Rola rack you mentioned. You'd want the Yakima Round Bar Rack part numbers # Y00408, # Y53TR, # Y03536, and # Y00233 which would fit and work well on your vehicle and with the Sunseeker. You will also need the adapter part # RR32105 too with the round bars.
view full answer... - How to Install Rhino-Rack Pioneer Platform Rack on a 2003 Hummer H2To install a platform rack on your 2003 Hummer H2 we first need a roof rack and for that I recommend the Yakima JetStream system that includes the following parts: - 60" JetStream Crossbars # Y00426 - SkyLine Towers # Y53TR - Landing Pad 4 # Y00224 This installs directly to the fixed mounting points on your Hummer which then allows you to use the Rhino-Rack Pioneer Platform Tray # RR82TB along with 2 of the Mounting Kit # RR43105 to get it installed. The Pioneer Platform # RR85ZW...
view full answer... - Recommended Roof Rack for 2024 Toyota RAV4For an extremely quiet roof rack that fits your 2024 Toyota RAV4 with flush mounted rails I recommend the Yakima JetStream roof rack. You will need the following: -Yakima JetStream Crossbars - Aluminum - Black - 50" Long # Y00425 -SkyLine Towers for Yakima Crossbars - Fixed Mounting Points, Flush Rails, and Track Systems # Y53TR -Landing Pad 23 for Yakima SkyLine and Control Towers # Y98FR The JetStream bars use an asymmetrical design along with WindRidges to reduce drag, noise, and...
view full answer... - Recommend Roof Rack for a Bike and Kayak on a 2018 Honda CR-VIn order to add a roof rack to your 2018 Honda CR-V I recommend using the Yakima Roof Rack made of parts # Y01156, # Y53TR, # Y03541 and # Y00245. This system has heavy duty yet lightweight aluminum cross bars that are durable and rustproof. This option will also be far more cost effective than an OEM roof rack as I am sure you will come to find out. If you need a kayak carrier then I recommend the Rhino-Rack Nautic Roof Kayak Carrier part # RR570. It is side-loading and it comes with...
view full answer... - Length of Yakima Crossbars Needed to Load 2 Thule Hullavators # TH898 on a 2019 Honda PilotWhile we do technically have an option for mounting 2 Hullavators # TH898 onto your 2019 Honda Pilot with the Yakima SkyLine Towers # Y53TR and Landing Pad 19 # Y00245 on your flush rails, you would need at least 72" inches of usable crossbar space for the required 4-8 inches of length past the feet. This is because one Hullavator measures 36" long. The 70" JetStream crossbars # Y00427 does not provide enough length. With that being said, the only Yakima option we carry that has that length...
view full answer... - Can Thule Hullavator Install on Yakima CrossbarsThe Thule Hullavator Pro # TH898 can fit round bars by grabbing around the crossbar and can fit aero shaped bars if the bars have a channel on top of them. Which the Yakima aero shaped bars don't have top channels so to go the Yakima route will require round bars which includes the part numbers # Y00408, # Y53TR, # Y03536, and # Y00241 and you'd be set.
view full answer... - Is There A Trailer Hitch For 2023 Kia Soul GT Line With Center ExhaustIf you need to carry cargo with your Kia Soul, I do have a few potential solutions for you. I will tell you there is not a trailer hitch available anywhere that will fit the center exhaust model at this time (August 2023). The receiver would go exactly where the exhaust sits and there is no way to work around that. If your goal was to carry a few bikes we could set you up with a trunk mount bike rack like the Malone hanger # MPG2139. This can carry 3 bikes weighing up to 33 lbs apiece...
view full answer... - Recommended Roof Rack for Hullavator and Kayak Carrier on 2019 Honda PilotThank you for all of the information! While you are able to use the Hullavator # TH898 with your setup as far as weight goes, this kayak carrier does require the crossbars to stick out 4" - 8" out past the roof rack feet. Since the Thule SquareBars have a limited amount of space under them for the feet you can only use the 53" Bars # TH712400 but this wouldn't give you the required spacing for the Hullavator. I recommend using the Yakima 60" JetStream Crossbar # Y00426 instead with the...
view full answer... - Will the Rhino-Rack # Y01-130B Fit My 2022 Hyundai Santa Cruz?Yes, you will be able to put 2 bikes on the Rhino-Rack Heavy-Duty Bar Roof Rack for Camper Shells - Track Mount # Y01-130B if the combined weight of the racks and bikes is exactly 220 pounds (or under). As far as the fitment of the # Y01-130B on your 2022 Hyundai Santa Cruz, that is a bit more complicated. The tracks will fit with the included hardware with drilling. With the 63" tracks, you can cut the tracks to the size of the bed rails. The complicated part is the crossbar fitment....
view full answer... - Parts To Use Existing Yakima Aero bars With RetraxONE For Toyota TacomaIt is possible to use your Yakima Aero bars on the RetraxONE part # RTT-60851 for the 2017 Toyota Tacoma. You need 2 sets of landing pads part # Y00221 to slide into the tracks of the Retrax system. You need one set (quantity of 4) of Yakima Skyline Towers part # Y53TR to attach to the landing pads. Then the Aero bars mount to the towers.
view full answer... - Are There Landing Pads Available To Mount Yakima Q-Towers To An A.R.E. Truck Topper I reached out to Yakima and was informed that there unfortunately is not a compatible landing pad for Q-Towers available so the only way to mount your Yakima crossbars would be to also get new towers. You would also need some tracks to mount on the roof of your A.R.E. Truck Topper to have something for the towers to mount to. We have the following track sizes available: 42" # Y01126 54" # Y01127 60" # Y01135 Since you have Q-Towers I'm assuming you have round bars and would need four...
view full answer... - How To Identify A Set of Roof Tracks On A Camper ShellIf you were to measure the width of the track that would then give you the best chance of identifying it. However, this really is not needed because the slots are pretty much universal so you can mix and max brands. The most cost effective system we would have is going to be a Yakima Round Bar System. The round crossbars are cut to fit. In order to obtain this you will need to order the following: Round 78" CrossBars for Yakima Roof Rack System part # Y00411 (Qty 1) Replacement Yakima...
view full answer... - Parts to Make a Rhino Rack Vortex bars fit with Snugtop Roof Rack RailsThe setup you need for your track system on your SnugTop which is made by Yakima will consist of four components. part # Y53TR SkyLine Towers for Yakima Crossbars Track Systems part # Y00221 Landing Pad 1 for Yakima Control Towers part # Y00422 Yakima CoreBar Crossbars - Steel - Black - 60" Long - Qty 2 part # Y07204 Yakima Same Key System (SKS) Lock Cores (QTY 4) These components will allow you to attach any roof mounted accessories you may want.
view full answer... - Cross Bars And Bike Rack Recommendation For Pace Edwards Tonneau Cover With Ultragroove RailsWhile there isn't something like the RockyMounts Truck Bed Track for Fork Mount Bike Racks # RKY10992 that is available and can be mouned into the Ultragroove rails on your Pace Edwards tonneau cover I do have another solution. Instead, you could mount a set of crossbars like Yakima JetStream Crossbars # Y00426, with the Landing Pad 1 for Yakima SkyLine and Control Towers # Y00221, and the BaseLine Towers for Yakima Crossbars # Y28TR, and connect them to the T-track in your tonneau cover. From...
view full answer... - Longest Rhino Rack Roof Rack Track Availability and Can Yakima Racks fit ThemI'll use your numbering for each of your questions so that they are easy for you to find. A. The longest track is actually the part # RRRTS518 which measures 92-5/16 inches long. B. These tracks are compatible with Yakima roof rack setups. The Landing Pad1 part # Y00221, the control towers, # Y00152, and crossbars, # Y00409 and round bar adapter # Y03536 would be what you need to install a Yakima rack in the tracks. C. The tracks will be limited by the weight capacity of the rack installed...
view full answer... - Hard Tonneau Cover Bike Rack for 2019 Ram 2500 Short BedWe do not have a bike carrier that mounts directly to a hard tonneau cover, however there is another solution. If you have room on you bed rail outside of the tonneau cover you can mount the equivilent of a roof rack on your bed rails using the following parts. Skyline Towers # Y53TR Yaamkia Landing Pads and control towers # Y00221 Yakima 58" Crossbars # Y00409 Yakima Round Bar Adapter # 8003536 With a complete rack system built you need only to choose the "roof" bike carriers that...
view full answer... - Parts Needed to Install Roof Rack on 1999 VW Euro VanI may have a solution for you, but I'm not showing any roof racks that are going to connect directly to any fixed mounting points or via rain gutters. You could go one of two directions with this that would allow you to mount a roof platform like the Yakima LockNLoad Platform Roof Tray # Y05044 on your 1999 VW Eurovan. You could use something like the SeaSucker Monkey Bars Roof Rack - Vacuum Cup Mount - 48" Long - Black # 298-SX6000B, which are the easiest to install option since they...
view full answer... - How To Use Yakima Round Crossbars With Tracks On Bed RailsIn order to use round crossbars on top of the bed rails you'll have to start with the tracks; then you can add the feet, landing pads, and crossbars. The feet are only offered in one height unfortunately but nonetheless I will attach a list of all the parts you'll need below. There isn't an all inclusive kit. Yakima Roof Track part # Y01127 Landing Pads part # Y00221 (2) Mounting Foot part # Y8890027 (4) Round Crossbars part # Y00411 (Cut To Fit)
view full answer... - Will The iKamper 2.0 Fit Yakima CrossBarsAccording to iKamper's website, their product mounts to most cross bars due to its universal design, however since we do not carry their products I can not confirm this. With that being said, since they say it is universal, you can absolutely use the Flexible Track Rack System # Y01127, with the landing pads # Y00221, and the control towers # Y8890027 to mount the iKamper 2.0 on your 2008 Toyota Tundra. Depending how wide your roof is, you can use the 66" crossbars # Y00410, the 58"...
view full answer... - Can Yakima Tracks Work on Truck Cap and RoofYou can add the Yakima Tracks for Roof Racks, which come in 60" # Y01135, 54" # Y01127 or 42" # Y01126 to your 2015 Ford F-150 although I could not tell from the photo if there was a space between the truck cap and the roof of your truck. If there is a space between them you wouldn't want to install just the two tracks per side as that wouldn't be fully secure. As for the rivets showing, they won't specifically, but the CapNuts in the hardware would show because you need to drill through...
view full answer...
- Available Roof Racks for Various Roof Styles on 1987 Jeep CherokeeWe can help you with a roof rack for your 1987 Jeep Cherokee. The rack fits depend on how the Cherokee's roof is set up. On the linked page just click on the picture that shows your roof style; you will then see only the racks that fit that type of roof. We have options from several brands but none of the roof configurations shows a fit for a SportRack brand roof rack. However, I can help you find the most cost-effective option for each type of roof. If you have a factory roof rack with...
view full answer... - What Tracks and Crossbars do You Recommend for My 2009 Volkswagen Routan with a Naked Roof? We do have an option that will allow you to mount long crossbars on your roof with tracks. This application requires drilling. For that setup, I recommend the following parts: - Yakima 42" Tracks for Roof Racks # Y01126 - x4 of the Yakima Control Towers # Y8890027 - x2 of the Landing Pad 1 for Yakima SkyLine and Control Towers # Y00221 - Round 58" CrossBars for Yakima Roof Rack System # Y00409 The Yakima RoundBar setup is compatible with most Thule cargo boxes and other branded cargo...
view full answer...
- Will Installing Track Roof Rack System on A.R.E. Topper Void WarrantyInstalling a track system roof rack like the Yakima parts # Y01126, # Y00221, # Y8890027, and # Y00410 won't void the warranty for your pickup but from what I could find it looks like modifying your A.R.E. topper will void that warranty. Since we aren't an A.R.E. dealer I can't really confirm this, but from my research it is very likely that your warranty will be void. So you can have the track system professionally installed but that would be your choice whether you want to pursue this...
view full answer...
- Landing Pads for the Yakima TracksIf you have Yakima tracks like part # Y01135, these accept the Yakima Landing Pad 1, part # Y00221. These connect to the Yakima Control Towers. They come in a pack of 2, so for two bars you will need to get two of these (to make 4). If you have different towers or tracks, let me know and I will help you find what you need.
view full answer... - How To Install Yakima LockNLoad Over Truck Bed with Tonneau CoverIn order to install the Yakima LockNLoad Platform Roof Tray above a tonneau cover on a truck bed you will need to install a set of tracks alongside the bed rails along with a crossbar system. The crossbar system is needed because the tray is not wide enough to reach just the mounting feet on the tracks. I have attached the needed parts below: Yakima JetStream Crossbars part # Y00427 Yakima Tracks for Roof Racks part # Y01135 Landing Pad Yakima Control Towers part # Y00221 (2) SkyLine Towers...
view full answer... - Roof Rack Option For 2016 Toyota 4Runner With Factory RailsThe standard roof rack fits for your 2016 Toyota 4Runner are all designed for the factory raised rails, but since you said you were okay with drilling holes you could add a track system to your roof. You would use whichever length is right for your 4Runner, the Yakima 42" Tracks for Roof Racks # Y01126 or 54" Tracks # Y01127. Then you'd just need the following: - Yakima JetStream Crossbars # Y00425 - SkyLine Towers # Y53TR - Landing Pad 1 # Y00221 You'd need a total of four of the...
view full answer... - What Landing Pads do I Need to Use the 54 Yakima Tracks # Y01127?For the Yakima Tracks - 54" # Y01127, you need a set of the Landing Pad 1 for Yakima SkyLine and Control Towers - Qty 2 # Y00221 for each crossbar. In addition to that, to have a complete setup, I recommend using the SkyLine Towers for Yakima Crossbars - Track Systems - Qty 4 # Y53TR and the Yakima JetStream Crossbars - Aluminum - Black # Y00425 (50 inches) or the # Y00426 (60 inches).
view full answer... - How To Mount Yakima Towers In Retrax Tonneau Cover TracksIf you have the Yakima Skyline or Control Towers then you can use the Landing Pad 1 for Yakima SkyLine and Control Towers part # Y00221 to mount them into tracks/channels like those found on select Retrax Tonneau Covers.
view full answer... - What Is Needed To Install Surco Safari Rack Onto A 1999 Ford Explorer SportTo install the Surco Safari Rack 5.0 Rooftop Cargo Basket # SPS5060-Y400 onto your 1999 Ford Explorer Sport 2 door you will first need to have the Yakima Crossbar system installed onto your vehicle. If you do not have the Yakima Crossbar system you will need the parts below: Yakima CoreBar Crossbars # Y00421 SkyLine Towers for Yakima Crossbars # Y53TR Landing Pad 1 for Yakima SkyLine and Control Towers # Y00221 The three parts above will give you the needed crossbar set up to be able...
view full answer... - Recommendation for Roof Rack 2014 Honda Odyssey with Naked RoofA 2014 Honda Odyssey with a naked roof is a rarity. The vast majority of those vans came with factory installed rails. Although there isn't a custom fit rack available, we can still get a roof rack on your Odyssey. I recommend going with the Yakima 54 Inch Tracks, # Y01127, or the 60 Inch Tracks, # Y01135 for your Odyssey. You will want to measure the roof of your Odyssey to see which size will work best for you. This track permanently mounts to your vehicle with PlusNut hardware. There...
view full answer... - Roof Rack Recommendation for 2022 Mercedes Benz Sprinter 2500 High RoofYes we have the Yakima HD roof rack that fits your 2022 Mercedes-Benz Sprinter 2500 with part numbers # Y01158, # Y00148, # Y03541, and # Y00221. What's great about this rack is that it has a much higher weight capacity, is still aerodynamic shaped, and also has a lifetime warranty.
view full answer... - Parts Needed to Add Yakima Crossbars to Retrax Tonneau Cover with T-Slot RailsFor your setup I recommend the TrackTowers for Yakima Crossbars and Platforms - Track Mount # Y52AV which includes everything you need to mount Yakima crossbars to your Retrax cover (unless you plan on using the Round or HD bars - then you'll need an additional adapter). To mount the SkyLine Towers # Y53TR to your tonneau cover you would need the 2 of the Landing Pad 1 # Y00221 kits as well which is why I recommend the first kit I mentioned. Most truck ladder racks use longer crossbars...
view full answer... - Will the Rhino-Rack # Y01-130B Fit My 2022 Hyundai Santa Cruz?Yes, you will be able to put 2 bikes on the Rhino-Rack Heavy-Duty Bar Roof Rack for Camper Shells - Track Mount # Y01-130B if the combined weight of the racks and bikes is exactly 220 pounds (or under). As far as the fitment of the # Y01-130B on your 2022 Hyundai Santa Cruz, that is a bit more complicated. The tracks will fit with the included hardware with drilling. With the 63" tracks, you can cut the tracks to the size of the bed rails. The complicated part is the crossbar fitment....
view full answer... - Parts To Use Existing Yakima Aero bars With RetraxONE For Toyota TacomaIt is possible to use your Yakima Aero bars on the RetraxONE part # RTT-60851 for the 2017 Toyota Tacoma. You need 2 sets of landing pads part # Y00221 to slide into the tracks of the Retrax system. You need one set (quantity of 4) of Yakima Skyline Towers part # Y53TR to attach to the landing pads. Then the Aero bars mount to the towers.
view full answer... - Are There Landing Pads Available To Mount Yakima Q-Towers To An A.R.E. Truck Topper I reached out to Yakima and was informed that there unfortunately is not a compatible landing pad for Q-Towers available so the only way to mount your Yakima crossbars would be to also get new towers. You would also need some tracks to mount on the roof of your A.R.E. Truck Topper to have something for the towers to mount to. We have the following track sizes available: 42" # Y01126 54" # Y01127 60" # Y01135 Since you have Q-Towers I'm assuming you have round bars and would need four...
view full answer... - How To Identify A Set of Roof Tracks On A Camper ShellIf you were to measure the width of the track that would then give you the best chance of identifying it. However, this really is not needed because the slots are pretty much universal so you can mix and max brands. The most cost effective system we would have is going to be a Yakima Round Bar System. The round crossbars are cut to fit. In order to obtain this you will need to order the following: Round 78" CrossBars for Yakima Roof Rack System part # Y00411 (Qty 1) Replacement Yakima...
view full answer... - Parts to Make a Rhino Rack Vortex bars fit with Snugtop Roof Rack RailsThe setup you need for your track system on your SnugTop which is made by Yakima will consist of four components. part # Y53TR SkyLine Towers for Yakima Crossbars Track Systems part # Y00221 Landing Pad 1 for Yakima Control Towers part # Y00422 Yakima CoreBar Crossbars - Steel - Black - 60" Long - Qty 2 part # Y07204 Yakima Same Key System (SKS) Lock Cores (QTY 4) These components will allow you to attach any roof mounted accessories you may want.
view full answer... - Cross Bars And Bike Rack Recommendation For Pace Edwards Tonneau Cover With Ultragroove RailsWhile there isn't something like the RockyMounts Truck Bed Track for Fork Mount Bike Racks # RKY10992 that is available and can be mouned into the Ultragroove rails on your Pace Edwards tonneau cover I do have another solution. Instead, you could mount a set of crossbars like Yakima JetStream Crossbars # Y00426, with the Landing Pad 1 for Yakima SkyLine and Control Towers # Y00221, and the BaseLine Towers for Yakima Crossbars # Y28TR, and connect them to the T-track in your tonneau cover. From...
view full answer... - Longest Rhino Rack Roof Rack Track Availability and Can Yakima Racks fit ThemI'll use your numbering for each of your questions so that they are easy for you to find. A. The longest track is actually the part # RRRTS518 which measures 92-5/16 inches long. B. These tracks are compatible with Yakima roof rack setups. The Landing Pad1 part # Y00221, the control towers, # Y00152, and crossbars, # Y00409 and round bar adapter # Y03536 would be what you need to install a Yakima rack in the tracks. C. The tracks will be limited by the weight capacity of the rack installed...
view full answer... - Hard Tonneau Cover Bike Rack for 2019 Ram 2500 Short BedWe do not have a bike carrier that mounts directly to a hard tonneau cover, however there is another solution. If you have room on you bed rail outside of the tonneau cover you can mount the equivilent of a roof rack on your bed rails using the following parts. Skyline Towers # Y53TR Yaamkia Landing Pads and control towers # Y00221 Yakima 58" Crossbars # Y00409 Yakima Round Bar Adapter # 8003536 With a complete rack system built you need only to choose the "roof" bike carriers that...
view full answer... - Parts Needed to Install Roof Rack on 1999 VW Euro VanI may have a solution for you, but I'm not showing any roof racks that are going to connect directly to any fixed mounting points or via rain gutters. You could go one of two directions with this that would allow you to mount a roof platform like the Yakima LockNLoad Platform Roof Tray # Y05044 on your 1999 VW Eurovan. You could use something like the SeaSucker Monkey Bars Roof Rack - Vacuum Cup Mount - 48" Long - Black # 298-SX6000B, which are the easiest to install option since they...
view full answer... - How To Use Yakima Round Crossbars With Tracks On Bed RailsIn order to use round crossbars on top of the bed rails you'll have to start with the tracks; then you can add the feet, landing pads, and crossbars. The feet are only offered in one height unfortunately but nonetheless I will attach a list of all the parts you'll need below. There isn't an all inclusive kit. Yakima Roof Track part # Y01127 Landing Pads part # Y00221 (2) Mounting Foot part # Y8890027 (4) Round Crossbars part # Y00411 (Cut To Fit)
view full answer... - Will The iKamper 2.0 Fit Yakima CrossBarsAccording to iKamper's website, their product mounts to most cross bars due to its universal design, however since we do not carry their products I can not confirm this. With that being said, since they say it is universal, you can absolutely use the Flexible Track Rack System # Y01127, with the landing pads # Y00221, and the control towers # Y8890027 to mount the iKamper 2.0 on your 2008 Toyota Tundra. Depending how wide your roof is, you can use the 66" crossbars # Y00410, the 58"...
view full answer... - Can Yakima Tracks Work on Truck Cap and RoofYou can add the Yakima Tracks for Roof Racks, which come in 60" # Y01135, 54" # Y01127 or 42" # Y01126 to your 2015 Ford F-150 although I could not tell from the photo if there was a space between the truck cap and the roof of your truck. If there is a space between them you wouldn't want to install just the two tracks per side as that wouldn't be fully secure. As for the rivets showing, they won't specifically, but the CapNuts in the hardware would show because you need to drill through...
view full answer... - Available Roof Racks for Various Roof Styles on 1987 Jeep CherokeeWe can help you with a roof rack for your 1987 Jeep Cherokee. The rack fits depend on how the Cherokee's roof is set up. On the linked page just click on the picture that shows your roof style; you will then see only the racks that fit that type of roof. We have options from several brands but none of the roof configurations shows a fit for a SportRack brand roof rack. However, I can help you find the most cost-effective option for each type of roof. If you have a factory roof rack with...
view full answer... - What Tracks and Crossbars do You Recommend for My 2009 Volkswagen Routan with a Naked Roof? We do have an option that will allow you to mount long crossbars on your roof with tracks. This application requires drilling. For that setup, I recommend the following parts: - Yakima 42" Tracks for Roof Racks # Y01126 - x4 of the Yakima Control Towers # Y8890027 - x2 of the Landing Pad 1 for Yakima SkyLine and Control Towers # Y00221 - Round 58" CrossBars for Yakima Roof Rack System # Y00409 The Yakima RoundBar setup is compatible with most Thule cargo boxes and other branded cargo...
view full answer... - Will Installing Track Roof Rack System on A.R.E. Topper Void WarrantyInstalling a track system roof rack like the Yakima parts # Y01126, # Y00221, # Y8890027, and # Y00410 won't void the warranty for your pickup but from what I could find it looks like modifying your A.R.E. topper will void that warranty. Since we aren't an A.R.E. dealer I can't really confirm this, but from my research it is very likely that your warranty will be void. So you can have the track system professionally installed but that would be your choice whether you want to pursue this...
view full answer... - Landing Pads for the Yakima TracksIf you have Yakima tracks like part # Y01135, these accept the Yakima Landing Pad 1, part # Y00221. These connect to the Yakima Control Towers. They come in a pack of 2, so for two bars you will need to get two of these (to make 4). If you have different towers or tracks, let me know and I will help you find what you need.
view full answer... - How To Install Yakima LockNLoad Over Truck Bed with Tonneau CoverIn order to install the Yakima LockNLoad Platform Roof Tray above a tonneau cover on a truck bed you will need to install a set of tracks alongside the bed rails along with a crossbar system. The crossbar system is needed because the tray is not wide enough to reach just the mounting feet on the tracks. I have attached the needed parts below: Yakima JetStream Crossbars part # Y00427 Yakima Tracks for Roof Racks part # Y01135 Landing Pad Yakima Control Towers part # Y00221 (2) SkyLine Towers...
view full answer... - Roof Rack Option For 2016 Toyota 4Runner With Factory RailsThe standard roof rack fits for your 2016 Toyota 4Runner are all designed for the factory raised rails, but since you said you were okay with drilling holes you could add a track system to your roof. You would use whichever length is right for your 4Runner, the Yakima 42" Tracks for Roof Racks # Y01126 or 54" Tracks # Y01127. Then you'd just need the following: - Yakima JetStream Crossbars # Y00425 - SkyLine Towers # Y53TR - Landing Pad 1 # Y00221 You'd need a total of four of the...
view full answer... - What Landing Pads do I Need to Use the 54 Yakima Tracks # Y01127?For the Yakima Tracks - 54" # Y01127, you need a set of the Landing Pad 1 for Yakima SkyLine and Control Towers - Qty 2 # Y00221 for each crossbar. In addition to that, to have a complete setup, I recommend using the SkyLine Towers for Yakima Crossbars - Track Systems - Qty 4 # Y53TR and the Yakima JetStream Crossbars - Aluminum - Black # Y00425 (50 inches) or the # Y00426 (60 inches).
view full answer... - How To Mount Yakima Towers In Retrax Tonneau Cover TracksIf you have the Yakima Skyline or Control Towers then you can use the Landing Pad 1 for Yakima SkyLine and Control Towers part # Y00221 to mount them into tracks/channels like those found on select Retrax Tonneau Covers.
view full answer... - What Is Needed To Install Surco Safari Rack Onto A 1999 Ford Explorer SportTo install the Surco Safari Rack 5.0 Rooftop Cargo Basket # SPS5060-Y400 onto your 1999 Ford Explorer Sport 2 door you will first need to have the Yakima Crossbar system installed onto your vehicle. If you do not have the Yakima Crossbar system you will need the parts below: Yakima CoreBar Crossbars # Y00421 SkyLine Towers for Yakima Crossbars # Y53TR Landing Pad 1 for Yakima SkyLine and Control Towers # Y00221 The three parts above will give you the needed crossbar set up to be able...
view full answer... - Recommendation for Roof Rack 2014 Honda Odyssey with Naked RoofA 2014 Honda Odyssey with a naked roof is a rarity. The vast majority of those vans came with factory installed rails. Although there isn't a custom fit rack available, we can still get a roof rack on your Odyssey. I recommend going with the Yakima 54 Inch Tracks, # Y01127, or the 60 Inch Tracks, # Y01135 for your Odyssey. You will want to measure the roof of your Odyssey to see which size will work best for you. This track permanently mounts to your vehicle with PlusNut hardware. There...
view full answer... - Roof Rack Recommendation for 2022 Mercedes Benz Sprinter 2500 High RoofYes we have the Yakima HD roof rack that fits your 2022 Mercedes-Benz Sprinter 2500 with part numbers # Y01158, # Y00148, # Y03541, and # Y00221. What's great about this rack is that it has a much higher weight capacity, is still aerodynamic shaped, and also has a lifetime warranty.
view full answer... - Parts Needed to Add Yakima Crossbars to Retrax Tonneau Cover with T-Slot RailsFor your setup I recommend the TrackTowers for Yakima Crossbars and Platforms - Track Mount # Y52AV which includes everything you need to mount Yakima crossbars to your Retrax cover (unless you plan on using the Round or HD bars - then you'll need an additional adapter). To mount the SkyLine Towers # Y53TR to your tonneau cover you would need the 2 of the Landing Pad 1 # Y00221 kits as well which is why I recommend the first kit I mentioned. Most truck ladder racks use longer crossbars...
view full answer...
Do you have a question about this Roof Rack?
Info for this part was:
Edited by:
Daron K
Written by:
Alex H
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.