Will the Yates Endcap for Side Guide Rollers - Heavy-Duty Rubber - 1/2" Shaft Leave Marks

Question

Question:

does black end caps for side roller leave black marks on boat

asked by: Victor C

0

Expert Reply:

The Yates Endcap for Side Guide Rollers part # YR224-4 can leave marks on the boat but we do have a non-marking option for you in the Yates Endcap for Boat Trailer Rollers part # YR131-4Y that won't.

expert reply by: Conner L

0

Answer 1

We have a 10 inch keel roller with the part #YR10000 which then for the endcaps you'd just need the part #YR134-5. You may also be interested a new bracket like part #CE10304G and a roller shaft part #CE10726A.

view full answer...

Answer 2

If you wanted to cut down the Yates Side Guide Roller #YR12243-4P that you referenced you certainly could. It's made of rubber so it would cut pretty easily.

view full answer...

Answer 3

TPR stands for thermal plasticized rubber. The Yates Endcap for Boat Trailer Rollers #YR131-4Y that you referenced is made of TPR so yes.

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb…

view full answer...

Answer 6

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 7

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 8

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Will the Yates Endcap for Side Guide Rollers - Heavy-Duty Rubber - 1/2" Shaft Leave Marks

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching