Can The Valterra RV Water Tank Be Mounted Horizontally Or Vertically?

Question

Question:

Can I mount the tank horizontally? So that 8 inches is the height?

asked by: Bill W

0

Expert Reply:

Yes, the Valterra RV Water Tank # R8042 can be mounted vertically or horizontally.

Additionally, doing this would also make the height 8" tall, like you mention.

expert reply by: Bryce D

0

Answer 1

The Valterra RV Water Tank #R8042 has 6 ports (3 on each side) to allow for different ways to mount your tank. One hole is already cut out with a red plug but the rest would require you to drilling out the hole before attaching your plumbing to the…

view full answer...

Answer 2

For use with the Valterra Rocket Water Hand Pump #RP800 we offer several sizes of fresh water tanks. Part #R8012, 6 gallon, 12 x 8 x 16-inches Part #R8018, 9 gallon, 18 x 8 x 16-inches Part #R8036, 18 gallon, 36 x 8 x 16-inches We do not have a 1 or…

view full answer...

Answer 3

You'd actually want to drill out the fill ports on the Valterra RV Water Tank #R8036 and not punch them out. You'd then want to rinse the tank out to get all of the debris out from the drilling.

view full answer...

Answer 4

The reason you can't use an electric pump with the Valterra RV Water Tank #R8036 is because they are made from lightweight plastic, and is baffled for surge control so they aren't designed to withstand the additional pressure that is created…

view full answer...

Answer 5

Yes, the Valterra RV Water Tank #R8036 can be installed vertically or horizontally without impacting its performance.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Can The Valterra RV Water Tank Be Mounted Horizontally Or Vertically?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching