Do You Carry the Pollak HD 7-Pole Round Connector 11-702?

Question

Question:

Are you a distributor of Pollak ? I am searching for trailer plug Pollak 11-702.

asked by: Sandra A

0

Expert Reply:

Yes! We do carry the Pollak connector you need. The 11-702 is the same as the Pollak HD, 7-Pole Round Pin Connector w/Cable Guard # PK11702. Sometimes manufacturers use different part numbers than what we use here at etrailer.

expert reply by: Bob C

0

Answer 1

There is an adapter for you that will allow the 7-way blade connector (sometimes called a 7-way flat) on your GMC truck to work with the 7-way round connector on your trailer. If you take a look at the accompanying photo, that's what your…

view full answer...

Answer 2

7-way trailer connectors can be wired in several ways and heavy-duty commercial/agricultural round-pin 7-way wiring can be different too. Please refer to the linked image to see the different vehicle-side connectors and their common wiring…

view full answer...

Answer 3

We do offer a range of wiring adapters for U.S. standard trailer wiring to convert from, for example, 7-way to 4-way, 5-way or 6-way wiring. These various connector types are shown in the linked article on trailer wiring. However, European trailer…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Do You Carry the Pollak HD 7-Pole Round Connector 11-702?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching