Trailer Hitch Recommendation for a 1997 Honda Accord Wagon
Question:
I have this hitch,can I use in a 1997 honda accord wagon?
asked by: Ana
Expert Reply:
The Curt trailer hitch # C11290 will only fit as far back as a 1998 Accord, not a 1997. The designs of the frame or other components between the 2 years are not similar enough to use the same hitches.
For a 1997 Honda Accord Wagon we have 1 hitch option, # C11205. This is a Class I trailer hitch. If you plan on using a hitch for accessories such as a bike rack or cargo carrier then Curt requires the use of a stabilization strap, # 18050, for all non-trailer loads.
If you plan on doing some towing first check the owners manual for the towing capacity of the vehicle. For a ball mount use # C45521. For a 1-7/8 inch ball use # 19256, for a 2 inch ball use # 19258, and for a pin and clip use # PC2. And for trailer wiring use # C56175. I have linked some instructions for you.
Products Referenced in This Question
Curt Cam Buckle Stabilizing Strap for Hitch-Mounted Accessories - 61" x 1" - Qty 1
- Accessories and Parts
- Hitch Bike Racks
- Hitch Cargo Carrier
- Tie Down Straps
- CURT
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Pin and Clip for 1-1/4" Hitches - 1/2" Diameter
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- No Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Where Does A Trailer Wiring Harness Plug In On A 2020 Subaru Crosstrek
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Can the Kuat Sherpa 2.0 Bike Rack Carry a Bike with a 48 Wheelbase
- Q&A: Hitch Tube Length of Curt Hitch # C11327
- Q&A: Does Curt Hitch C11327 Fit a 2006 Honda Accord Sedan with Dual Exhaust
- Q&A: Hitch Pin Hole to Outer Most Edge of Bumper Measurement on Trailer Hitch for 2003 Acura TL
- Q&A: Where are the Attachement Points for Curt Trailer Hitch # C11290 on a 2003 Honda Accord
- Q&A: Can a Class II Yakima Bike Rack be Used in a Class I Draw-Tite Hitch on a 1999 Honda Accord
- Article: Hitch Adapters and Extenders
- Article: Trailer Tire Sizing
- Article: Trailer Wiring Diagrams
- Article: Trailer Hitch Installation Tips
- Article: My Trailer Hitch Doesn't Fit