2010 Ford F-150 Black Ladder Rack Recommendation to Fit with Folding Tonneau Cover

Question

Question:

Do you have any black ladder racks that work with w tri-fold bed cover? Thanks

asked by: Charlie H

0

Expert Reply:

As long as the tonneau cover rails sit inside the bed rails on your 2010 Ford F-150 you can use the Adarac Pro Series Custom Truck Bed Ladder Rack in the matte black style. This is a sliding rack with rails that install on top of the bed rails and there is enough space between the legs for you to fold up your cover without any issues. The correct rack will depend on the length of your truck bed:

5-1/2' - # A86RR
6-1/2' - # A58RR
8' - # A26RR

If the rails of your tonneau cover sit on top of your bed rails then we'll have to either go with a roof rack over your cab or look at a different tonneau cover in order to add some cargo carrying space on your pickup.

expert reply by: Jon G

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 3

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 4

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 5

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 6

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

The #37213635 JR Products Replacement Landing Gear Switch you'd mentioned would be a proper replacement for your existing Atwood 70254 landing gear switch. If you wanted the switch, wiring harness and the bezel for the switch, use the Stromberg…

view full answer...

Answer 9

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

Actually our etrailer.com brand brake assemblies are rebranded AxleTek assemblies. So we have the 8k left and right assembly set #AKEBRK-8 which is most likely what you need but these are 12-1/4 inch in diameter by 3-3/8 inches wide and attach with a…

view full answer...

2010 Ford F-150 Black Ladder Rack Recommendation to Fit with Folding Tonneau Cover

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching