Warranty Length for Replacement Hydraulic Pump Motor for Lippert Hydraulic Power Unit

Question

Question:

How long is the warranty on this motor?

asked by: Karl J

0

Expert Reply:

The warranty length of the Replacement Hydraulic Pump Motor for Lippert Hydraulic Power Unit # LC167576 that you referenced is 1 year.

expert reply by: Jameson C

0

Answer 1

It sounds like the ground isn't the issue because you bypass that with the cables and still have the clicking of the solenoid #LC118246. It sounds like the solenoid has gone bad and needs replacing. You have confirmed the motor works, so…

view full answer...

Answer 2

Yes; this could potentially be an issue with the solenoid and there is a way to test whether or not this is the cause of the issues. What you'll need to do is switch the wiring between the two cylinders to see if the same thing happens, but…

view full answer...

Answer 3

I do have some things for you to check but there is not really a reset button for the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System. The first thing you will need to do is obtain a multimeter. Once you have this then you will…

view full answer...

Answer 4

I went ahead and reached out Lippert and they were able to tell me that the mounting screws on the Replacement 2-Quart Pump Reservoir Kit for Lippert Components Hydraulic Power Unit #LC46FR measure 3" from the top screw to the bottom screw, and…

view full answer...

Answer 5

The bearing is not included with the Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K part #TJD-12000-RODNUT. There is a bearing washer at the top but the bearing is sold separately as the Replacement Bearing for etrailer…

view full answer...

Answer 6

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

I looked up pictures of the taillights that are on the 3110 Featherlite trailers and for the LED version of them you would want the part #STL36RB and #STL37RB. It looks like the spare tire mounts for your trailer are something you would have to get…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Warranty Length for Replacement Hydraulic Pump Motor for Lippert Hydraulic Power Unit

Product Page this Question was Asked From

Continue Researching