Replacement Brackets for Toy Hauler Ladder

Question

Question:

Do you have the brackets that hold the ladder in place on a toy hauler?

asked by: Nich

0

Expert Reply:

We have some of the support pegs like part # 8531-B which is designed for the Universal Ladder # LA-401BA, but we don't have any hardware designed around the OEM ladders. If your OEM ladder is in bad shape then I recommend replacing it entirely with this ladder as opposed to trying to piece some parts together and hope that it works.

expert reply by: Jon G

0

Answer 1

The Stromberg Carlson RV Exterior Ladder w/ Hinges, #LA-401 and #LA-401BA (black) is an aluminum ladder that is 99-1/2" Tall by 12" Wide. If needed, there is the Surco RV Ladder Extension, #SP504L that is a 30-1/2" in length. By…

view full answer...

Answer 2

Easiest way it to measure vertically between the mounting holes of the pin box. If they are 2 inches apart up and down then you have a 1621. If that distance is instead 2-1/2 inches then you have a 1716. The part #LC1191191 that you referenced is for…

view full answer...

Answer 3

Basically the biggest difference between a Lippert 1116 and a Lippert 1716 is that the 1716 extends out further than the 1116. The 1716 is considered a long pin box whereas the 1116 is considered a medium length. The length difference will be 5-3/4…

view full answer...

Answer 4

The Lippert Trailair Air Ride 5th Wheel Pin Box #LC155943 is a direct bolt-on replacement for the Lippert 1116 OEM pin box. The air-cushioned Trailair provides a smoother ride by reducing chucking and jarring and it comes fully assembled. It is rated…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 8

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

While trailer axles do feature an upward bend like you are describing, there isn't a particular amount/measurement that is standard across the board. This bend in the axle is designed so that it will straighten under a trailer's loaded…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Replacement Brackets for Toy Hauler Ladder

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching