Adapter for 2020 Ram 2500 with OEM Prep Package to Use Andersen Ultimate Connection

Question

Question:

I have a 2020 Ram 2500 with the factory puck system. Do they make a rail system that will fit my puck system to accommodate an Anderson ultimate hitch system?

asked by: Terry C

0

Expert Reply:

You could use the Ram rail kit adapter part # RP30154 installed in the OEM rails of your 2020 Ram 2500 and you'd have a set of rails compatible with the Andersen Ultimate # AM3200.

expert reply by: Jameson C

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 4

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 5

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 6

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 7

The correct tie-downs for your 2019 Ram 3500 Tradesman short bed depend on your hitch. You can choose from the following: With a factory installed hitch or non-Torklift aftermarket hitch -TorkLift Talon Camper Tie-Downs #TL52XR (front) and #TL34FR…

view full answer...

Answer 8

Hey Steve, so between the Curt #C16265 and the Pullrite #PUL36ZR I'd go wit the Curt but not the Q25. I'd go with the A25 #C24FR, which is basically the same thing as the Q25 but does not require the #C88KR adapter. Only the Curt is going to…

view full answer...

Answer 9

Most standard pin boxes will not make a 90 degree turn in anything less than an 8 foot truck bed, but that is due to being too close to the cab - not the rails. You mentioned you wanted to replace the Rota-Flex with the Gen-Y hitch. Your old pin box…

view full answer...

Answer 10

As long as the RBW Lil' Rocker mounts to industry standard base rails you'll need the Curt Adapter Rails #C29BR that fit in the OEM puck system on your 2019 Ram 2500 and give you a standard base rail connection. I'm attaching a photo…

view full answer...

Answer 11

Yes, the #TLD2142 is exactly what you need for your 2019 Ram 3500 with running boards extending under the truck bed. For the rear, you need the #TLD3112 if you have the factory hitch or #TLR3510 if you have the TorkLift SuperHitch Magnum 30K.

view full answer...

Answer 12

The factory prep package or pucks are not the same between Ram, GM and Ford. The spacing is all different which means you cannot use a 5th wheel hitch for Ram pucks on a GM with pucks. Take the Curt A25 5th Wheel Trailer Hitch for example which is…

view full answer...

Adapter for 2020 Ram 2500 with OEM Prep Package to Use Andersen Ultimate Connection

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching