Replacement Handle for Reese Round Tube Slider for 5th Wheel Trailer Hitches

Question

Question:

I have a Reese tube slider base #50024, need new slider handle kit and cant seem to find. Is there a compatible kit for this base? I see one for the square slides but not sure if it will work with the tube slide base. Thanks

asked by: Andy N

0

Expert Reply:

I reached out to Reese (Horizon Global) about this and they said that the # 58161 square handle is not compatible and they discontinued the service kit. That being said, my contact told me if you can provide original proof of purchase they will be able to get the replacement part for you. If you are unable to provide this then the only option would be to purchase the entire # RP50024 slider unfortunately.

expert reply by: Robin H

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but…

view full answer...

Answer 4

The absolute best cushioned equalizer that fits the dimensions you mentioned having would be the MORryde ALLTREK 4000 part #MR89DR as this is only option to provide vertical and horizontal cushioning. This would make a big difference and…

view full answer...

Answer 5

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is…

view full answer...

Answer 6

Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is. This may be difficult as some wheels and covers will make this…

view full answer...

Answer 7

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 8

The hangers you currently have on your trailer are ones I have run into before. That being said, I spoke with MORryde and the #MR27ZR will still fit your trailer, but there is a modification that will need to be made. You’ll have to trim according to…

view full answer...

Answer 9

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 10

Hi David; nope, the leaf springs don't need to be changed if going to the AllTrek 4000 equalizers. You just need to choose the right one based on your wheelbase (measured center-to-center of your wheels): - 33" Wheelbase: MORryde AllTrek…

view full answer...

Answer 11

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Replacement Handle for Reese Round Tube Slider for 5th Wheel Trailer Hitches

Products Referenced in This Question

Featured Help Information

Miscellaneous Media

Continue Researching