Fulton Marine 1.5K Sidewind Trailer Jack XPD15L0126

Question

Question:

Looking for a Fulton XPD15LO126 trailer jack.

asked by: Keith M

0

Expert Reply:

Then that means you're looking for the Fulton Bolt-Thru Swivel Marine Jack with Dual Wheels # F27CR. We use different part numbers on our site compared to the manufacturers, but this is the exact trailer jack you're wanting.

Attached is a review video for you to check out.

expert reply by: Jon G

0

Answer 1

Fulton bolt-through trailer jack #F1411300301 is the only Fulton jack that mounts using that 1 center bolt. Since your old jack was a Fulton it must either be this same jack or an earlier model but they use the same mount. The mount in question and…

view full answer...

Answer 2

The Fulton Bolt-Thru Swivel Marine Jack part #FXP10W0301 is held on to the trailer with a center bolt. It is also the pivot bolt. Use a box end wrench or a short wall socket to remove the existing bolt. It has pretty coarse threads and generally they…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

While I don't know exactly what landing gear you have on your 2011 Keystone Raptor 3812 Toy Hauler, I can say that you should be able to replace them with the Landing Gear Set w/ Handle #RVLG-8HDL as this landing gear uses the standard weld mount…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 10

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Fulton Marine 1.5K Sidewind Trailer Jack XPD15L0126

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching