Cotter Pin Replacement Part for 5,200 lb Axles

Question

Question:

Do you sell the Cotter Pin separately that is in this kit?....I just need a bunch of those pins. Bearing Kit, LM67048/25580 Bearings, GS-2125DL Seal Item # BK3-310

asked by: James C

0

Expert Reply:

We do sell the cotter pin separately from the Bearing Kit # BK3-310, you're looking for the Cotter Pin - 1/8" Thick x 1-3/4" Long # 165649.

expert reply by: Jon G

0

Answer 1

We do have the Dexter Electric Brake Kit part #23-105-106-09 which is 2, 12 inch brake assemblies that can be mounted with a 4 or 5 inch bolt pattern. The 4 bolt pattern that is found on AL KO trailer axles like what you have now so it would be…

view full answer...

Answer 2

I checked with Dexter, and they say for their 12 inch brakes, the Dexter Electric Trailer Brake Kit - 12" - Left and Right Hand Assemblies - 6,000 lbs #23-105-106, the torque should be between 25-50 ft. lbs. For the mounting hardware…

view full answer...

Answer 3

We have an article to assist with checking your brake magnets like you are stating. The resistance will go down because the brake magnets are connected in parallel. Since the voltage doesn't change, the amperage draw needs to increase to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard…

view full answer...

Answer 6

That really depends on the material of your rim and the diameter of your wheel studs. If you have a steel wheel with a 1/2 inch stud you would use 90-120 ft/lbs. Steel with 9/16 inch stud 120-140 ft/lbs. Aluminum with 1/2 inch stud 90-100 ft/lbs.…

view full answer...

Answer 7

You are looking for the Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2 part #RG06-050 just like the ones you previously ordered two of these come in a pack.

view full answer...

Answer 8

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

The Dexter Electric Trailer Brake Kit #23-105-106 are a replacement set for the 023-358-00. This kit includes a right and left brake assembly that is manually adjustable. I recommend the Dexter Nev-R-Adjust Electric Trailer Brake Kit #23-458-459 as…

view full answer...

Cotter Pin Replacement Part for 5,200 lb Axles

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching