Class III Trailer Hitch that Fits 2022 Toyota Venza

Question

Question:

Does the Toyota Venza hitch class 3 2021 fits the 2022?

asked by: Ulises L

0

Expert Reply:

We do have a hitch that fits your 2022 Toyota Venza with the Curt # C76HR but at this time the Draw Tite you mentioned has not been officially carried over to the 2022 model.

expert reply by: Jameson C

0

Answer 1

I pulled up the online owners manual of your 2022 Toyota Venza and Toyota states that it is not recommended to tow with your vehicle which is why they also do not list a towing capacity. So this begs the very valid question of why do we have hitches…

view full answer...

Answer 2

Absolutely, and the best trailer hitch receiver for your 2023 Toyota Venza is going to be either the Curt or etrailer hitch. I mention both because they are the same hitch, just with different finishes - the Curt has a glossy finish while the…

view full answer...

Answer 3

We actually do have a trailer wiring harness that is a fit for your 2021 Toyota Venza, but since it was redesigned for the 2021 model year, the part number you mentioned won't work. Instead, the exact wiring harness that I verified from the…

view full answer...

Answer 4

Depending on how comfortable you are with wiring/vehicle electrical, there's two routes you could go to equip your 2022 Hyundai Palisade for towing your surge coupler equipped boat trailer. The least complicated way to do this would be to install…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Class III Trailer Hitch that Fits 2022 Toyota Venza

Products Referenced in This Question

Featured Help Information

Instructions

Continue Researching