Replacement Fan Motor And Blade For Ventline P Series Range Hood

Question

Question:

I need to replace my fan motor on my hood to my stove I live in a camper model number is phcc0431-09 its a 2013 feather light by Rockwood

asked by: Teri W

0

Expert Reply:

It sounds like your current fan motor is apart of the Ventline P series range hoods. In that case, you'll want to use the Replacement Fan Motor for Ventline Range Hoods # BVD0278-00. If you also need the replacement fan blade as well, you can use the Replacement Fan Blade for Ventline RV Range Hood # BCD0311-00.

expert reply by: Bryce D

0

Answer 1

The operating instructions for the Curt Triflex brake controller #C24VV, which are linked for you, indicate on page 19 that if the unit displays the error code A.E. this indicates an internal fault with the controller's accelerometer. This is not…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 5

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

We can definitely get you set up. For a 7-way wiring harness for your 2024 Honda Pilot trailsport I recommend the Curt T-Connector #C35ZV which will plug in to the existing tow package connector at the rear your vehicle. I do also recommend getting…

view full answer...

Answer 8

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 9

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...

Answer 10

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Replacement Fan Motor And Blade For Ventline P Series Range Hood

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching