What is Difference Between Axles Dexter part # 20545I-EZ-72-15 and etrailer # e37YR

Question

Question:

What is the difference between this axle and part # e37YR. They appear to have the same specs. Thanks

asked by: Paul A

0

Expert Reply:

The two axles you referenced, the Dexter part # 20545I-EZ-72-15 and the etrailer # e37YR are essentially the same axle made by two different companies but the specs are the same. They are both 2,000 lb axles that are 72 inches long with spring center dimensions of 58 inches with idler hubs that have a 5 on 4-1/2 inch bolt pattern. Most will argue that the Dexter axles are the highest quality so that would be what I would go with if I were you.

expert reply by: Jameson C

0

Answer 1

Unfortunately, we do not have any hubs that match the dimensions you provided. The only other option I have for you at this time would be to replace the axle. If you can provide me with the hub face to hub face and spring center to spring center…

view full answer...

Answer 2

We have a couple options for 72" hubs. I have linked a diagram that will show you what dimensions you are looking for so you can ensure that's what you need on your 1993 Jayco Eagle 10 trailer. Also you may be able to find an axle tag or…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 10

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...