Keying A Pop & Lock Tailgate Lock To A 2011 Toyota Tacoma Ignition Key

Question

Question:

Do you sell a keyed cylinder to leaner my igintion key? Regards

asked by: Walter H

1

Helpful Expert Reply:

The Pop & Lock Custom Locking Tailgate Handle # PAL5409 uses a BOLT branded lock cylinder so you would just need to insert your vehicle's key in the core and turn it as far as you can clockwise. Once this has been done the lock will be keyed to your vehicle.

expert reply by: Kevin C

1

Answer 1

The Pop & Lock Custom Tailgate Handle #PAL85510 is the correct fit for your 2015 Toyota Tacoma. Since you have a camera you'll want to also pick up the Camera Mounting Clip for Pop & Lock Custom Locking Tailgate Handle #PL5455CAMB and can…

view full answer...

Answer 2

I can help you out, no problem. What you are going to want to look at is the towing capacities of the truck. You need to know the gross combined weight rating. This is the most the vehicle, including cargo and occupants, plus the trailer can weigh.…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

Assuming your tires are in good shape without any bulges the easiest way to determine if you have a bent spindle is to take a straight edge that is longer than the tire and lay it across the tire parallel with your trailer frame and then measure the…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Keying A Pop & Lock Tailgate Lock To A 2011 Toyota Tacoma Ignition Key

Product Page this Question was Asked From

Continue Researching