Can B&W Turnover Ball Gooseneck Hitch Be Installed on RamBox Equipped 2022 Ram 2500

Question

Question:

Will the B&W gooseneck hitch fit on my RamBox equipped 2022 Ram 2500?

asked by: Sharon

0

Expert Reply:

According to the fine folks at B&W hitch, having the Rambox option on your truck won't prevent you from installing and using a B&W Turnover Ball gooseneck hitch on your 2022 Ram 2500.

You'll want to use the # BWGNRK1320 which will bolt up to the existing rails already in place under your truck bed. You'll just need to cut the hole in the bed and bolt up the hitch.

If you'd like to install a 7-way trailer connector in the truck bed so you don't have to run the trailer connector up over the tailgate, you can do so using part # C56000.

expert reply by: Mike L

0

Answer 1

Yes, it does. The B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs, part #BWGNRK1320, does come with a drill diagram. It is not a traditional template. It is a metal piece that you will use with the…

view full answer...

Answer 2

For your 2002 Starcraft Constellation Series camper with a Dexter 3,500 lb. axle 10" x 2-1/4" drum, the replacement electric trailer brake assemblies, are #23-27 for right hand side, and #23-26 for the left; #23-26-27, for the combined kit.…

view full answer...

Answer 3

There is a 5th wheel hitch that fits your 2021 Ram 2500 with the factory 5th wheel prep package that is considered to be the best in the industry, which is the B&W Companion OEM 5th Wheel Trailer Hitch with Slider for Ram Towing Prep Package…

view full answer...

Answer 4

Yes! The B&W Turnoverball #BWGNRK1320 fits your 2022 Ram 2500 with a 6-1/2 foot bed and Rambox. However, it is important to note that you need to make sure you have appropriate clearance of the bed rails with a trailer attached the the…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 10

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 11

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 12

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...