Lift Kit for Weekend Warrior 3505 for Towing Level with Bed Clearance

Question

Question:

Hi Guys, I have a 2020 Chevy Duramax 2500 and tow a Weekend Warrior 3505 fifth wheel. The combo tows awesome however I have hit the truck bed rails once so far on really uneven desert roads when turning into a campsite. If I the pin on the fifth down the fifth wheel angle is too high. If I leave everything like it is I am totally level but too close to the bed when turning on uneven ground. What do you suggest?

asked by: David T

0

Expert Reply:

Best solution would be to install a lift kit on your Weekend Warrior 3505 so that you could then lower your pin box in your frame brackets to gain more clearance while still towing your trailer level. For a triple axle lift kit you'd want the part # RR55QX. This will give you a lift of up to 2-1/4 inches.

expert reply by: Jameson C

0

Answer 1

The Road Armor Shock Absorbing Equalizer Kit part #LC696740 are taller than most other standard equalizers so you'll likely need the longer 3-1/8" shackle straps when using them, the Lippert AP Kit part #LC52SV is a go-to for this as it has…

view full answer...

Answer 2

In order to raise your triple axle car trailer the amount you are looking for, you are going to need to install an axle flip kit along with a set of leaf spring hanger extensions. For an axle flip kit, I recommend the Dexter Trailer Springs…

view full answer...

Answer 3

We offer two versions of the Dexter Axle Over-Under Conversion kit, often called a flip kit, that are to be selected based on the diameter of the trailer's axles. Kit #K71-384-00 works with 2-3/8-inch diameter axles and kit #K71-385-00 works on…

view full answer...

Answer 4

I recommend upgrading to the MORryde Shock Absorbing Suspension Equalizers #MR59ZR for your triple axle 5th wheel camper. These are designed for axle spacings of 33". You will need to select one of the wet bolt kits from the list below. There…

view full answer...

Answer 5

Thank you for providing all your axle information Orrie. I do see your 2014 Forest River R-Pod 177 does have the #10 Torflex which would use the Lift Kit #K71-707-01. This provides 2-5/8" of additional ground clearance. You are not going to…

view full answer...

Answer 6

I am happy to verify for you that your 2023 Nissan Frontier Pro 4X is 100% compatible with the Draw-Tite front hitch that fits, which is the following part number: - Draw-Tite Front Mount Trailer Hitch Receiver #65075 So you will have no issues…

view full answer...

Answer 7

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 8

For 1/2 inch trailer u-bolts that attach to axle the recommended torque value is between 45 and 70 ft lbs of torque.

view full answer...

Answer 9

I contacted Lippert and the Road Armor Shock Absorbing Equalizer Kit part #LC696740 is compatible with the Lippert Components Correct Track Trailer Alignment and 2" Lift Kit part #LC87120. If you use the road armor equalizers you will not need…

view full answer...

Answer 10

The answer is yes, rather than the Equa-Flex, the longer-lasting and better quality is the MORryde Shock Absorbing Suspension Equalizers for Triple Axle Trailers w/ 33" Wheelbase #MR59ZR. The rubber on the MORryde #MR59ZR won't last forever,…

view full answer...

Answer 11

When measuring an axle to determine the weight capacity you'll want to measure along the actual axle tube. Anywhere between the spring seats will work fine. I also recommend measuring with a digital caliper like #PTW80157 to get an accurate…

view full answer...